[Bug 35638] Re: Printer is not detected properly over USB
george whitmore
george.p.whitmore at gmail.com
Sun Mar 30 22:48:47 UTC 2008
Hi Till
This is the lsusb and lsusb -vvv:
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 002 Device 002: ID 04b4:4100 Cypress Semiconductor Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x04b4 Cypress Semiconductor Corp.
idProduct 0x4100
bcdDevice 0.02
iManufacturer 1
iProduct 2 USB PRINT
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 50
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 4
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 2
bNumEndpoints 2
bInterfaceClass 7 Printer
bInterfaceSubClass 1 Printer
bInterfaceProtocol 2 Bidirectional
iInterface 0
** UNRECOGNIZED: 09 21 10 01 00 01 22 25 00
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
cannot read device status, Broken pipe (32)
Bus 002 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.24-12-generic uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1a.1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0103 power enable connect
Port 2: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 001 Device 003: ID 0a5c:2110 Broadcom Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 224 Wireless
bDeviceSubClass 1 Radio Frequency
bDeviceProtocol 1 Bluetooth
bMaxPacketSize0 64
idVendor 0x0a5c Broadcom Corp.
idProduct 0x2110
bcdDevice 1.00
iManufacturer 1 Broadcom Corp
iProduct 2 BCM2045B
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 216
bNumInterfaces 4
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 224 Wireless
bInterfaceSubClass 1 Radio Frequency
bInterfaceProtocol 1 Bluetooth
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0010 1x 16 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 224 Wireless
bInterfaceSubClass 1 Radio Frequency
bInterfaceProtocol 1 Bluetooth
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0000 1x 0 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0000 1x 0 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 1
bNumEndpoints 2
bInterfaceClass 224 Wireless
bInterfaceSubClass 1 Radio Frequency
bInterfaceProtocol 1 Bluetooth
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0009 1x 9 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0009 1x 9 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 2
bNumEndpoints 2
bInterfaceClass 224 Wireless
bInterfaceSubClass 1 Radio Frequency
bInterfaceProtocol 1 Bluetooth
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0011 1x 17 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0011 1x 17 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 3
bNumEndpoints 2
bInterfaceClass 224 Wireless
bInterfaceSubClass 1 Radio Frequency
bInterfaceProtocol 1 Bluetooth
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 4
bNumEndpoints 2
bInterfaceClass 224 Wireless
bInterfaceSubClass 1 Radio Frequency
bInterfaceProtocol 1 Bluetooth
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 5
bNumEndpoints 2
bInterfaceClass 224 Wireless
bInterfaceSubClass 1 Radio Frequency
bInterfaceProtocol 1 Bluetooth
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 3
bAlternateSetting 0
bNumEndpoints 0
bInterfaceClass 254 Application Specific Interface
bInterfaceSubClass 1 Device Firmware Update
bInterfaceProtocol 0
iInterface 0
** UNRECOGNIZED: 07 21 07 88 13 40 00
Device Status: 0x0001
Self Powered
Bus 001 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.24-12-generic uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1a.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0103 power enable connect
Port 2: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
This dmesg:
[ 23.291293] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) ->
IRQ 16
[ 23.291297] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 23.291330] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 20 (level, low) ->
IRQ 17
[ 23.291338] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 23.291374] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 21 (level, low) ->
IRQ 18
[ 23.291379] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 23.291408] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 22 (level, low) ->
IRQ 19
[ 23.291415] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 23.291442] ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 23 (level, low) ->
IRQ 20
[ 23.291447] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[ 23.291476] ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 20 (level, low) ->
IRQ 17
[ 23.291483] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 23.291502] PCI: Enabling device 0000:00:1e.0 (0005 -> 0007)
[ 23.291510] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 23.291535] ACPI: PCI Interrupt 0000:15:00.0[A] -> GSI 16 (level, low) ->
IRQ 16
[ 23.291543] PCI: Setting latency timer of device 0000:15:00.0 to 64
[ 23.291552] NET: Registered protocol family 2
[ 23.328632] IP route cache hash table entries: 32768 (order: 5, 131072
bytes)
[ 23.328798] TCP established hash table entries: 131072 (order: 8, 1048576
bytes)
[ 23.329121] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 23.329276] TCP: Hash tables configured (established 131072 bind 65536)
[ 23.329278] TCP reno registered
[ 23.340661] checking if image is initramfs... it is
[ 23.849782] Freeing initrd memory: 7279k freed
[ 23.849915] Simple Boot Flag at 0x35 set to 0x1
[ 23.850430] audit: initializing netlink socket (disabled)
[ 23.850441] audit(1206901419.304:1): initialized
[ 23.850500] highmem bounce pool size: 64 pages
[ 23.852209] VFS: Disk quotas dquot_6.5.1
[ 23.852108] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 23.852213] io scheduler noop registered
[ 23.852215] io scheduler anticipatory registered
[ 23.852216] io scheduler deadline registered
[ 23.852224] io scheduler cfq registered (default)
[ 23.852397] Boot video device is 0000:01:00.0
[ 23.852497] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 23.852529] assign_interrupt_mode Found MSI capability
[ 23.852556] Allocate Port Service[0000:00:01.0:pcie00]
[ 23.852583] Allocate Port Service[0000:00:01.0:pcie02]
[ 23.852657] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 23.852746] assign_interrupt_mode Found MSI capability
[ 23.852812] Allocate Port Service[0000:00:1c.0:pcie00]
[ 23.852837] Allocate Port Service[0000:00:1c.0:pcie02]
[ 23.852965] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 23.853049] assign_interrupt_mode Found MSI capability
[ 23.853122] Allocate Port Service[0000:00:1c.1:pcie00]
[ 23.853147] Allocate Port Service[0000:00:1c.1:pcie02]
[ 23.853266] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 23.853339] assign_interrupt_mode Found MSI capability
[ 23.853405] Allocate Port Service[0000:00:1c.2:pcie00]
[ 23.853433] Allocate Port Service[0000:00:1c.2:pcie02]
[ 23.853560] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[ 23.853648] assign_interrupt_mode Found MSI capability
[ 23.853723] Allocate Port Service[0000:00:1c.3:pcie00]
[ 23.853753] Allocate Port Service[0000:00:1c.3:pcie02]
[ 23.853882] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 23.853963] assign_interrupt_mode Found MSI capability
[ 23.854034] Allocate Port Service[0000:00:1c.4:pcie00]
[ 23.854059] Allocate Port Service[0000:00:1c.4:pcie02]
[ 23.854307] isapnp: Scanning for PnP cards...
[ 24.212012] isapnp: No Plug & Play device found
[ 24.231682] Real Time Clock Driver v1.12ac
[ 24.231760] hpet_resources: 0xfed00000 is busy
[ 24.231798] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ
sharing enabled
[ 24.232774] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024
blocksize
[ 24.232824] input: Macintosh mouse button emulation as
/devices/virtual/input/input0
[ 24.232901] PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64
irq 1,12
[ 24.242773] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 24.242777] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 24.259218] mice: PS/2 mouse device common for all mice
[ 24.259303] EISA: Probing bus 0 at eisa.0
[ 24.259311] Cannot allocate resource for EISA slot 1
[ 24.259314] Cannot allocate resource for EISA slot 2
[ 24.259315] Cannot allocate resource for EISA slot 3
[ 24.259317] Cannot allocate resource for EISA slot 4
[ 24.259318] Cannot allocate resource for EISA slot 5
[ 24.259320] Cannot allocate resource for EISA slot 6
[ 24.259321] Cannot allocate resource for EISA slot 7
[ 24.259323] Cannot allocate resource for EISA slot 8
[ 24.259324] EISA: Detected 0 cards.
[ 24.259326] cpuidle: using governor ladder
[ 24.259328] cpuidle: using governor menu
[ 24.259388] NET: Registered protocol family 1
[ 24.259409] Using IPI No-Shortcut mode
[ 24.259431] registered taskstats version 1
[ 24.259546] Magic number: 0:967:393
[ 24.259592] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 24.259593] EDD information not available.
[ 24.259770] Freeing unused kernel memory: 364k freed
[ 24.264151] input: AT Translated Set 2 keyboard as
/devices/platform/i8042/serio0/input/input1
[ 25.425910] fuse init (API version 7.9)
[ 25.441476] ACPI: SSDT BFEE1B32, 02C4 (r1 PmRef Cpu0Ist 100 INTL
20050513)
[ 25.441711] ACPI: SSDT BFEE1E7B, 085E (r1 PmRef Cpu0Cst 100 INTL
20050513)
[ 25.444426] Monitor-Mwait will be used to enter C-1 state
[ 25.444428] Monitor-Mwait will be used to enter C-2 state
[ 25.444429] Monitor-Mwait will be used to enter C-3 state
[ 25.444533] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 25.444537] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 25.444709] ACPI: SSDT BFEE1A6A, 00C8 (r1 PmRef Cpu1Ist 100 INTL
20050513)
[ 25.444924] ACPI: SSDT BFEE1DF6, 0085 (r1 PmRef Cpu1Cst 100 INTL
20050513)
[ 25.447214] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[ 25.447217] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 25.449471] ACPI: Thermal Zone [THM0] (62 C)
[ 25.450901] ACPI: Thermal Zone [THM1] (61 C)
[ 25.698928] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
[ 25.698931] Copyright (c) 1999-2006 Intel Corporation.
[ 25.698976] ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 20 (level, low) ->
IRQ 17
[ 25.698988] PCI: Setting latency timer of device 0000:00:19.0 to 64
[ 25.713009] usbcore: registered new interface driver usbfs
[ 25.713028] usbcore: registered new interface driver hub
[ 25.720083] usbcore: registered new device driver usb
[ 25.722473] USB Universal Host Controller Interface driver v3.0
[ 25.725136] e1000: 0000:00:19.0: e1000_probe: (PCI Express:2.5Gb/s:Width
x1) 00:1e:37:88:46:68
[ 25.804841] SCSI subsystem initialized
[ 25.818242] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network
Connection
[ 25.818292] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 20 (level, low) ->
IRQ 17
[ 25.818305] PCI: Setting latency timer of device 0000:00:1a.0 to 64
[ 25.818311] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 25.818491] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus
number 1
[ 25.818530] uhci_hcd 0000:00:1a.0: irq 17, io base 0x00001860
[ 25.818637] usb usb1: configuration #1 chosen from 1 choice
[ 25.818654] hub 1-0:1.0: USB hub found
[ 25.818658] hub 1-0:1.0: 2 ports detected
[ 25.842078] libata version 3.00 loaded.
[ 25.919830] ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) ->
IRQ 18
[ 25.919843] PCI: Setting latency timer of device 0000:00:1a.1 to 64
[ 25.919849] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 25.919866] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus
number 2
[ 25.919901] uhci_hcd 0000:00:1a.1: irq 18, io base 0x00001880
[ 25.919988] usb usb2: configuration #1 chosen from 1 choice
[ 25.920007] hub 2-0:1.0: USB hub found
[ 25.920010] hub 2-0:1.0: 2 ports detected
[ 26.023717] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) ->
IRQ 16
[ 26.023727] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 26.023731] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 26.023747] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus
number 3
[ 26.023783] uhci_hcd 0000:00:1d.0: irq 16, io base 0x000018a0
[ 26.023873] usb usb3: configuration #1 chosen from 1 choice
[ 26.023890] hub 3-0:1.0: USB hub found
[ 26.023893] hub 3-0:1.0: 2 ports detected
[ 26.127592] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) ->
IRQ 21
[ 26.127605] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 26.127610] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 26.127626] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus
number 4
[ 26.127660] uhci_hcd 0000:00:1d.1: irq 21, io base 0x000018c0
[ 26.127748] usb usb4: configuration #1 chosen from 1 choice
[ 26.127765] hub 4-0:1.0: USB hub found
[ 26.127769] hub 4-0:1.0: 2 ports detected
[ 26.159463] usb 1-1: new full speed USB device using uhci_hcd and address
2
[ 26.175269] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) ->
IRQ 22
[ 26.175282] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 26.175287] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 26.175303] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus
number 5
[ 26.175334] uhci_hcd 0000:00:1d.2: irq 22, io base 0x000018e0
[ 26.175422] usb usb5: configuration #1 chosen from 1 choice
[ 26.175438] hub 5-0:1.0: USB hub found
[ 26.175442] hub 5-0:1.0: 2 ports detected
[ 26.180274] usb 1-1: configuration #1 chosen from 1 choice
[ 26.183539] ata_piix 0000:00:1f.1: version 2.12
[ 26.183555] ACPI: PCI Interrupt 0000:00:1f.1[C] -> GSI 16 (level, low) ->
IRQ 16
[ 26.183594] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[ 26.184206] scsi0 : ata_piix
[ 26.184328] scsi1 : ata_piix
[ 26.184987] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1830 irq
14
[ 26.184989] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1838 irq
15
[ 26.238695] Clocksource tsc unstable (delta = -304684913 ns)
[ 26.239392] usb 3-1: new full speed USB device using uhci_hcd and address
2
[ 26.244292] ata1.00: ATAPI: DVD/CDRW UJDA775, CB03, max UDMA/33
[ 26.248169] usb 3-1: configuration #1 chosen from 1 choice
[ 26.263946] ata1.00: configured for UDMA/33
[ 26.264067] ata2: port disabled. ignoring.
[ 26.265188] scsi 0:0:0:0: CD-ROM MATSHITA DVD/CDRW UJDA775
CB03 PQ: 0 ANSI: 5
[ 26.265344] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 22 (level, low) ->
IRQ 19
[ 26.265357] PCI: Setting latency timer of device 0000:00:1a.7 to 64
[ 26.265360] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 26.265380] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus
number 6
[ 26.269285] PCI: cache line size of 32 is not supported by device
0000:00:1a.7
[ 26.269294] ehci_hcd 0000:00:1a.7: irq 19, io mem 0xfe226c00
[ 26.274896] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10
Dec 2004
[ 26.274984] usb usb6: configuration #1 chosen from 1 choice
[ 26.275002] hub 6-0:1.0: USB hub found
[ 26.275006] hub 6-0:1.0: 4 ports detected
[ 26.280532] ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 19 (level, low) ->
IRQ 23
[ 26.280540] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 26.280543] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 26.280566] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus
number 7
[ 26.284488] ehci_hcd 0000:00:1d.7: debug port 1
[ 26.284495] PCI: cache line size of 32 is not supported by device
0000:00:1d.7
[ 26.284502] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfe227000
[ 26.288528] usb 3-2: new full speed USB device using uhci_hcd and address
3
[ 26.299281] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10
Dec 2004
[ 26.299351] usb usb7: configuration #1 chosen from 1 choice
[ 26.299368] hub 7-0:1.0: USB hub found
[ 26.299371] hub 7-0:1.0: 6 ports detected
[ 26.355253] usb 1-1: USB disconnect, address 2
[ 26.403348] ahci 0000:00:1f.2: version 3.0
[ 26.403379] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 16 (level, low) ->
IRQ 16
[ 26.403442] ahci 0000:00:1f.2: nr_ports (3) and implemented port map
(0x1) don't match, using nr_ports
[ 26.403444] ahci 0000:00:1f.2: forcing PORTS_IMPL to 0x7
[ 26.487290] usbcore: registered new interface driver libusual
[ 26.487136] usb 3-1: USB disconnect, address 2
[ 26.490791] Initializing USB Mass Storage driver...
[ 27.094175] usb 7-1: new high speed USB device using ehci_hcd and address
2
[ 27.227100] usb 7-1: configuration #1 chosen from 1 choice
[ 27.405939] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 1.5 Gbps
0x7 impl SATA mode
[ 27.405942] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum
part
[ 27.405951] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 27.406127] scsi2 : ahci
[ 27.406237] scsi3 : ahci
[ 27.406329] scsi4 : ahci
[ 27.406373] ata3: SATA max UDMA/133 abar m2048 at 0xfe226000 port 0xfe226100
irq 217
[ 27.406378] ata4: SATA max UDMA/133 abar m2048 at 0xfe226000 port 0xfe226180
irq 217
[ 27.406383] ata5: SATA max UDMA/133 abar m2048 at 0xfe226000 port 0xfe226200
irq 217
[ 27.465660] usb 7-2: new high speed USB device using ehci_hcd and address
3
[ 27.598228] usb 7-2: configuration #1 chosen from 1 choice
[ 27.598309] hub 7-2:1.0: USB hub found
[ 27.598418] hub 7-2:1.0: 4 ports detected
[ 27.702616] scsi5 : SCSI emulation for USB Mass Storage devices
[ 27.702657] usbcore: registered new interface driver usb-storage
[ 27.702660] USB Mass Storage support registered.
[ 27.702713] usb-storage: device found at 2
[ 27.702714] usb-storage: waiting for device to settle before scanning
[ 27.885081] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 27.885965] ata3.00: ATA-7: ST980825AS, 3.04, max UDMA/133
[ 27.885968] ata3.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 27.886991] ata3.00: configured for UDMA/133
[ 27.941165] usb 1-1: new full speed USB device using uhci_hcd and address
3
[ 28.111667] usb 1-1: configuration #1 chosen from 1 choice
[ 28.197804] ata4: SATA link down (SStatus 0 SControl 0)
[ 28.303470] usb 7-2.1: new full speed USB device using ehci_hcd and
address 4
[ 28.363645] usb 7-2.1: configuration #1 chosen from 1 choice
[ 28.389260] ata5: SATA link down (SStatus 0 SControl 0)
[ 28.389288] scsi 2:0:0:0: Direct-Access ATA ST980825AS
3.04 PQ: 0 ANSI: 5
[ 28.389723] ACPI: PCI Interrupt 0000:15:00.1[B] -> GSI 17 (level, low) ->
IRQ 21
[ 28.389735] PCI: Setting latency timer of device 0000:15:00.1 to 64
[ 28.442365] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[21]
MMIO=[f8101000-f81017ff] Max Packet=[2048] IR/IT contexts=[4/4]
[ 28.446239] Driver 'sd' needs updating - please use bus_type methods
[ 28.446287] sd 2:0:0:0: [sda] 156301488 512-byte hardware sectors (80026
MB)
[ 28.446296] sd 2:0:0:0: [sda] Write Protect is off
[ 28.446298] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 28.446310] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 28.446357] sd 2:0:0:0: [sda] 156301488 512-byte hardware sectors (80026
MB)
[ 28.446364] sd 2:0:0:0: [sda] Write Protect is off
[ 28.446366] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 28.446378] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 28.446380] sda:<4>Driver 'sr' needs updating - please use bus_type
methods
[ 28.459839] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[ 28.459842] Uniform CD-ROM driver Revision: 3.20
[ 28.459875] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 28.496803] sda1 sda2 < sda5 >
[ 28.497939] sd 2:0:0:0: [sda] Attached SCSI disk
[ 28.501222] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 28.501235] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 28.511246] usb 7-2.2: new full speed USB device using ehci_hcd and
address 5
[ 28.567603] usb 7-2.2: config 1 has an invalid descriptor of length 26,
skipping remainder of the config
[ 28.567608] usb 7-2.2: config 1 interface 0 has no altsetting 0
[ 28.571187] usb 7-2.2: configuration #1 chosen from 1 choice
[ 28.571348] usb 7-2.2: can't set config #1, error -32
[ 28.653736] Attempting manual resume
[ 28.653738] swsusp: Resume From Partition 8:5
[ 28.653740] PM: Checking swsusp image.
[ 28.654107] PM: Resume from disk failed.
[ 28.668950] kjournald starting. Commit interval 5 seconds
[ 28.668822] EXT3-fs: mounted filesystem with ordered data mode.
[ 28.683106] usb 7-2.3: new high speed USB device using ehci_hcd and
address 6
[ 28.740473] usb 7-2.3: configuration #1 chosen from 1 choice
[ 28.740785] scsi6 : SCSI emulation for USB Mass Storage devices
[ 28.740691] usb-storage: device found at 6
[ 28.740692] usb-storage: waiting for device to settle before scanning
[ 28.837835] usb 7-2.4: new low speed USB device using ehci_hcd and
address 7
[ 28.901288] usb 7-2.4: configuration #1 chosen from 1 choice
[ 28.957219] ieee1394: Host added: ID:BUS[0-00:1023]
GUID[00061b032a1d7487]
[ 29.242543] usb-storage: device scan complete
[ 29.243014] scsi 5:0:0:0: Direct-Access WD 1600BEVExternal
1.02 PQ: 0 ANSI: 0
[ 29.244650] sd 5:0:0:0: [sdb] 312581808 512-byte hardware sectors (160042
MB)
[ 29.245376] sd 5:0:0:0: [sdb] Write Protect is off
[ 29.245378] sd 5:0:0:0: [sdb] Mode Sense: 00 00 00 00
[ 29.245379] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[ 29.246268] sd 5:0:0:0: [sdb] 312581808 512-byte hardware sectors (160042
MB)
[ 29.246998] sd 5:0:0:0: [sdb] Write Protect is off
[ 29.247000] sd 5:0:0:0: [sdb] Mode Sense: 00 00 00 00
[ 29.247001] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[ 29.247003] sdb:<7>usb-storage: device scan complete
[ 29.992931] scsi 6:0:0:0: CD-ROM PLEXTOR DVDR PX-716A
1.07 PQ: 0 ANSI: 0 CCS
[ 30.416479] sdb1
[ 30.416561] sd 5:0:0:0: [sdb] Attached SCSI disk
[ 30.416593] sd 5:0:0:0: Attached scsi generic sg2 type 0
[ 30.422039] sr1: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
[ 30.422092] sr 6:0:0:0: Attached scsi CD-ROM sr1
[ 30.422121] sr 6:0:0:0: Attached scsi generic sg3 type 5
[ 30.774393] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 30.792204] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 31.322271] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 31.384869] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 31.407808] input: Power Button (FF) as /devices/virtual/input/input2
[ 31.425936] ACPI: Power Button (FF) [PWRF]
[ 31.425988] input: Lid Switch as /devices/virtual/input/input3
[ 31.426188] ACPI: Lid Switch [LID]
[ 31.426223] input: Sleep Button (CM) as /devices/virtual/input/input4
[ 31.457887] ACPI: Sleep Button (CM) [SLPB]
[ 31.540621] Linux agpgart interface v0.102
[ 31.762008] input: Video Bus as
/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:05/LNXVIDEO:01/input/input5
[ 31.784263] ACPI: Video Device [VID1] (multi-head: yes rom: no post:
no)
[ 31.796310] ACPI: WMI-Acer: Mapper loaded
[ 31.829453] ACPI: AC Adapter [AC] (on-line)
[ 31.885757] ACPI: Battery Slot [BAT0] (battery present)
[ 31.985349] nvidia: module license 'NVIDIA' taints kernel.
[ 32.316680] Bluetooth: Core ver 2.11
[ 32.339738] NET: Registered protocol family 31
[ 32.339740] Bluetooth: HCI device and connection manager initialized
[ 32.339743] Bluetooth: HCI socket layer initialized
[ 32.347617] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) ->
IRQ 16
[ 32.347626] PCI: Setting latency timer of device 0000:01:00.0 to 64
[ 32.347720] NVRM: loading NVIDIA UNIX x86 Kernel Module 169.12 Thu Feb
14 17:53:07 PST 2008
[ 32.390377] Bluetooth: HCI USB driver ver 2.9
[ 32.395766] usbcore: registered new interface driver hci_usb
[ 32.415287] iTCO_vendor_support: vendor-support=0
[ 32.417588] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
[ 32.417654] iTCO_wdt: Found a ICH8M-E TCO device (Version=2,
TCOBASE=0x1060)
[ 32.417689] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 32.708198] Yenta: CardBus bridge found at 0000:15:00.0 [17aa:20c6]
[ 32.717760] ricoh-mmc: Ricoh MMC Controller disabling driver
[ 32.717762] ricoh-mmc: Copyright(c) Philip Langdale
[ 32.808045] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection
driver for Linux, 1.2.0
[ 32.808048] iwl3945: Copyright(c) 2003-2007 Intel Corporation
[ 32.836826] Yenta: ISA IRQ mask 0x0cb8, PCI irq 16
[ 32.836832] Socket status: 30000006
[ 32.836834] pcmcia: parent PCI bridge I/O window: 0x8000 - 0xbfff
[ 32.836837] cs: IO port probe 0x8000-0xbfff: clean.
[ 32.837686] pcmcia: parent PCI bridge Memory window: 0xf8100000 -
0xfbffffff
[ 32.837687] pcmcia: parent PCI bridge Memory window: 0xf4000000 -
0xf7ffffff
[ 32.846099] sdhci: Secure Digital Host Controller Interface driver
[ 32.846102] sdhci: Copyright(c) Pierre Ossman
[ 32.853529] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) ->
IRQ 21
[ 32.853544] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 32.853562] iwl3945: Detected Intel PRO/Wireless 3945ABG Network
Connection
[ 33.035766] usbcore: registered new interface driver hiddev
[ 33.071866] input: Microsoft Microsoft USB Wireless Mouse as
/devices/pci0000:00/0000:00:1d.7/usb7/7-2/7-2.4/7-2.4:1.0/input/input6
[ 33.091659] input,hidraw0: USB HID v1.11 Mouse [Microsoft Microsoft USB
Wireless Mouse] on usb-0000:00:1d.7-2.4
[ 33.091671] usbcore: registered new interface driver usbhid
[ 33.091674] /build/buildd/linux-2.6.24/drivers/hid/usbhid/hid-core.c:
v2.6:USB HID core driver
[ 33.191036] input: PC Speaker as /devices/platform/pcspkr/input/input7
[ 33.305520] Non-volatile memory driver v1.2
[ 33.778398] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x81a0b1, caps:
0xa04793/0x300000
[ 33.778403] serio: Synaptics pass-through port at isa0060/serio1/input0
[ 33.822759] input: SynPS/2 Synaptics TouchPad as
/devices/platform/i8042/serio1/input/input8
[ 33.880052] sdhci: SDHCI controller found at 0000:15:00.2 [1180:0822]
(rev 21)
[ 33.880086] ACPI: PCI Interrupt 0000:15:00.2[C] -> GSI 18 (level, low) ->
IRQ 22
[ 33.880100] sdhci:slot0: Will use DMA mode even though HW doesn't fully
claim to support it.
[ 33.880107] PCI: Setting latency timer of device 0000:15:00.2 to 64
[ 33.880140] mmc0: SDHCI at 0xf8101800 irq 22 DMA
[ 33.905786] thinkpad_acpi: ThinkPad ACPI Extras v0.17
[ 33.905788] thinkpad_acpi: http://ibm-acpi.sf.net/
[ 33.905789] thinkpad_acpi: ThinkPad BIOS 7LETA9WW (2.09 ), EC
7KHT24WW-1.08
[ 33.905791] thinkpad_acpi: Lenovo ThinkPad T61
[ 33.908167] thinkpad_acpi: radio switch found; radios are enabled
[ 33.917933] thinkpad_acpi: standard ACPI backlight interface available,
not loading native one...
[ 33.918241] input: ThinkPad Extra Buttons as
/devices/virtual/input/input9
[ 33.941806] ricoh-mmc: Ricoh MMC controller found at
0000:15:00.3[1180:0843] (rev 11)
[ 33.941818] ricoh-mmc: Controller is now disabled.
[ 33.941915] ACPI: PCI Interrupt 0000:00:1b.0[B] -> GSI 17 (level, low) ->
IRQ 21
[ 33.941919] hda_intel: probe_mask set to 0x1 for device 17aa:20ac
[ 33.941934] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 33.985976] iwl3945: Tunable channels: 11 802.11bg, 13 802.11a channels
[ 34.006968] wmaster0: Selected rate control algorithm 'iwl-3945-rs'
[ 34.109139] cs: IO port probe 0x100-0x3af: clean.
[ 34.110902] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[ 34.111638] cs: IO port probe 0x820-0x8ff: clean.
[ 34.112216] cs: IO port probe 0xc00-0xcf7: clean.
[ 34.112983] cs: IO port probe 0xa00-0xaff: clean.
[ 34.217615] lp: driver loaded but no devices found
[ 34.307941] Adding 3229024k swap on /dev/sda5. Priority:-1 extents:1
across:3229024k
[ 34.430792] EXT3 FS on sda1, internal journal
[ 34.862788] ACPI: ACPI Dock Station Driver
[ 34.864083] ACPI: \_SB_.PCI0.IDE0.PRIM.MSTR: found ejectable bay
[ 34.864088] ACPI: \_SB_.PCI0.IDE0.PRIM.MSTR: Adding notify handler
[ 34.864107] ACPI: Error installing bay notify handler
[ 34.864110] ACPI: Bay [\_SB_.PCI0.IDE0.PRIM.MSTR] Added
[ 35.566241] apm: BIOS not found.
[ 35.610882] ppdev: user-space parallel port driver
[ 35.736428] input: /usr/sbin/thinkpad-keys as
/devices/virtual/input/input10
[ 36.139297] IBM TrackPoint firmware: 0x0e, buttons: 3/3
[ 36.364987] input: TPPS/2 IBM TrackPoint as
/devices/platform/i8042/serio1/serio2/input/input11
[ 36.848909] Bluetooth: L2CAP ver 2.9
[ 36.848916] Bluetooth: L2CAP socket layer initialized
[ 37.241130] Bluetooth: RFCOMM socket layer initialized
[ 37.241149] Bluetooth: RFCOMM TTY layer initialized
[ 37.241153] Bluetooth: RFCOMM ver 1.8
[ 50.219302] NET: Registered protocol family 10
[ 50.219877] lo: Disabled Privacy Extensions
[ 50.220967] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 50.222096] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 55.498593] CPU0 attaching NULL sched-domain.
[ 55.498604] CPU1 attaching NULL sched-domain.
[ 55.520256] CPU0 attaching sched-domain:
[ 55.520263] domain 0: span 03
[ 55.520267] groups: 01 02
[ 55.520274] CPU1 attaching sched-domain:
[ 55.520277] domain 0: span 03
[ 55.520281] groups: 02 01
[ 58.136547] kjournald starting. Commit interval 5 seconds
[ 58.136713] EXT3-fs warning: maximal mount count reached, running e2fsck
is recommended
[ 58.141290] EXT3 FS on sdb1, internal journal
[ 58.141295] EXT3-fs: mounted filesystem with ordered data mode.
[ 60.922044] NET: Registered protocol family 17
[ 61.761621] wlan0: Initial auth_alg=0
[ 61.761630] wlan0: authenticate with AP 00:12:17:bf:16:31
[ 61.763209] wlan0: RX authentication from 00:12:17:bf:16:31 (alg=0
transaction=2 status=0)
[ 61.763212] wlan0: authenticated
[ 61.763214] wlan0: associate with AP 00:12:17:bf:16:31
[ 61.765028] wlan0: RX AssocResp from 00:12:17:bf:16:31 (capab=0x411
status=0 aid=1)
[ 61.765031] wlan0: associated
[ 61.766677] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 61.925816] padlock: VIA PadLock not detected.
[ 69.090056] wlan0: no IPv6 routers present
[ 3891.812684] usb 7-2.2: USB disconnect, address 5
[ 3894.806444] usb 2-1: new full speed USB device using uhci_hcd and address
2
[ 3894.963081] usb 2-1: config 1 has an invalid descriptor of length 26,
skipping remainder of the config
[ 3894.963087] usb 2-1: config 1 interface 0 has no altsetting 0
[ 3894.994130] usb 2-1: configuration #1 chosen from 1 choice
[ 3895.130745] usblp0: USB Bidirectional printer dev 2 if 0 alt 2 proto 2
vid 0x04B4 pid 0x4100
[ 3895.130758] usbcore: registered new interface driver usblp
This is: ls -l /dev/usb/lp* /dev/usblp*
gpw at gpw-a:~$ ls -l /dev/usb/lp* /dev/usblp*
lrwxrwxrwx 1 root root 7 2008-03-30 17:45 /dev/usblp0 -> usb/lp0
crw-rw---- 1 root lp 180, 0 2008-03-30 17:45 /dev/usb/lp0
gpw at gpw-a:~$
Really pushing Firefox 3 beta 4 on this one...
On Sun, Mar 30, 2008 at 5:55 PM, Till Kamppeter <till.kamppeter at gmail.com>
wrote:
> George, for me it looks like that your computer is not discovering your
> printer at all. Is it turned on? Is it a USB printer? Is the cable OK?
>
> Can you do
>
> sudo lsusb
> sudo lsusb -vvv
> dmesg
> ls -l /dev/usb/lp* /dev/usblp*
>
> and post the output here?
>
> --
> Printer is not detected properly over USB
> https://bugs.launchpad.net/bugs/35638
> You received this bug notification because you are a direct subscriber
> of the bug.
>
** Attachment added: "unnamed"
http://launchpadlibrarian.net/12983752/unnamed
--
Printer is not detected properly over USB
https://bugs.launchpad.net/bugs/35638
You received this bug notification because you are a member of Kernel
Bugs, which is subscribed to linux-source-2.6.15 in ubuntu.
More information about the kernel-bugs
mailing list