I have what sounds like a berring going bad.
Steven Vollom
stevenvollom at sbcglobal.net
Sat Feb 21 00:20:47 UTC 2009
On Friday 20 February 2009 18:49:39 Willy Hamra wrote:
> sudo smartctl --all /dev/sda
Willie,
My 200gb drive seems OK, however the 80gb has a long list of Old Age and
prefail warnings. I would like to not lose the data on the drive and don't
have a place to put it right now, Should I disconnect the drive until I can
solve the storage problem?
The SMART overall-health self-assessment test result of the 200gb drive:
PASSED. Still there were 30 prefail or old age warnings on it too.
It is a lot of reading, so don't take the time if you choose not to, but I am
not qualified to make a decision on this. It really looks to me like both my
drives are at the end of their use. What would you do?
Here are the readings:
steven at Yesua:~$ sudo smartctl --all /dev/sda
[sudo] password for steven:
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Maxtor DiamondMax Plus 9 family
Device Model: Maxtor 6Y200P0
Serial Number: Y61LGAEE
Firmware Version: YAR41BW0
User Capacity: 203,928,109,056 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Fri Feb 20 18:54:38 2009 EST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 243) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 91) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
3 Spin_Up_Time 0x0027 176 001 063 Pre-fail Always
In_the_past 20225
4 Start_Stop_Count 0x0032 252 252 000 Old_age Always
- 2014
5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail Always
- 1
6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline -
0
7 Seek_Error_Rate 0x000a 253 252 000 Old_age Always
- 0
8 Seek_Time_Performance 0x0027 253 238 187 Pre-fail Always
- 56048
9 Power_On_Minutes 0x0032 183 183 000 Old_age Always
- 402h+41m
10 Spin_Retry_Count 0x002b 253 237 157 Pre-fail Always
- 0
11 Calibration_Retry_Count 0x002b 253 251 223 Pre-fail Always
- 0
12 Power_Cycle_Count 0x0032 248 248 000 Old_age Always
- 2151
192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always
- 0
193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always
- 0
194 Temperature_Celsius 0x0032 253 253 000 Old_age Always
- 39
195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always
- 1590
196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline -
0
197 Current_Pending_Sector 0x0008 253 253 000 Old_age Offline -
0
198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline -
0
199 UDMA_CRC_Error_Count 0x0008 029 001 000 Old_age Offline -
616
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always
- 0
201 Soft_Read_Error_Rate 0x000a 253 238 000 Old_age Always
- 58
202 TA_Increase_Count 0x000a 253 252 000 Old_age Always
- 0
203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always
- 2
204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always
- 0
205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always
- 0
207 Spin_High_Current 0x002a 253 237 000 Old_age Always
- 0
208 Spin_Buzz 0x002a 253 252 000 Old_age Always
- 0
209 Offline_Seek_Performnce 0x0024 193 188 000 Old_age Offline -
0
99 Unknown_Attribute 0x0004 253 253 000 Old_age Offline -
0
100 Unknown_Attribute 0x0004 253 253 000 Old_age Offline -
0
101 Unknown_Attribute 0x0004 253 253 000 Old_age Offline -
0
SMART Error Log Version: 1
Warning: ATA error count 972 inconsistent with error log pointer 5
ATA Error Count: 972 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 972 occurred at disk power-on lifetime: 19742 hours (822 days + 14
hours)
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 3c 8f aa 01 e0 Error: UNC 60 sectors at LBA = 0x0001aa8f = 109199
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 8f aa 01 e0 08 00:09:46.608 READ DMA
27 00 00 00 00 00 e0 08 00:09:46.592 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 0a 00:09:46.576 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 0a 00:09:46.576 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 08 00:09:46.576 READ NATIVE MAX ADDRESS EXT
Error 971 occurred at disk power-on lifetime: 19742 hours (822 days + 14
hours)
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 3c 8f aa 01 e0 Error: UNC 60 sectors at LBA = 0x0001aa8f = 109199
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 8f aa 01 e0 08 00:09:45.536 READ DMA
27 00 00 00 00 00 e0 08 00:09:45.520 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 0a 00:09:45.520 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 0a 00:09:45.504 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 08 00:09:45.504 READ NATIVE MAX ADDRESS EXT
Error 970 occurred at disk power-on lifetime: 19742 hours (822 days + 14
hours)
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 3c 8f aa 01 e0 Error: UNC 60 sectors at LBA = 0x0001aa8f = 109199
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 8f aa 01 e0 08 00:09:44.480 READ DMA
27 00 00 00 00 00 e0 08 00:09:44.464 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 0a 00:09:44.448 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 0a 00:09:44.448 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 08 00:09:44.448 READ NATIVE MAX ADDRESS EXT
Error 969 occurred at disk power-on lifetime: 19742 hours (822 days + 14
hours)
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 3c 8f aa 01 e0 Error: UNC 60 sectors at LBA = 0x0001aa8f = 109199
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 8f aa 01 e0 08 00:09:43.424 READ DMA
27 00 00 00 00 00 e0 08 00:09:43.408 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 0a 00:09:43.408 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 0a 00:09:43.392 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 08 00:09:43.392 READ NATIVE MAX ADDRESS EXT
Error 968 occurred at disk power-on lifetime: 19742 hours (822 days + 14
hours)
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 3c 8f aa 01 e0 Error: UNC 60 sectors at LBA = 0x0001aa8f = 109199
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 8f aa 01 e0 08 00:09:42.368 READ DMA
27 00 00 00 00 00 e0 08 00:09:42.336 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 0a 00:09:42.336 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 0a 00:09:42.336 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 08 00:09:42.336 READ NATIVE MAX ADDRESS EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Short captive Completed without error 00% 13926 -
# 2 Short captive Completed without error 00% 13575 -
# 3 Short captive Completed without error 00% 13560 -
# 4 Short captive Completed without error 00% 13559 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
steven at Yesua:~$ sudo smartctl --all /dev/sdb
[sudo] password for steven:
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Maxtor DiamondMax Plus 9 family
Device Model: Maxtor 6Y080P0
Serial Number: Y316LC4E
Firmware Version: YAR41BW0
User Capacity: 81,964,302,336 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Fri Feb 20 19:10:05 2009 EST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 182) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 40) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
3 Spin_Up_Time 0x0027 193 189 063 Pre-fail Always
- 18980
4 Start_Stop_Count 0x0032 252 252 000 Old_age Always
- 2127
5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail Always
- 1
6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline -
0
7 Seek_Error_Rate 0x000a 253 252 000 Old_age Always
- 0
8 Seek_Time_Performance 0x0027 253 244 187 Pre-fail Always
- 49538
9 Power_On_Minutes 0x0032 173 173 000 Old_age Always
- 613h+45m
10 Spin_Retry_Count 0x002b 253 246 157 Pre-fail Always
- 0
11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail Always
- 0
12 Power_Cycle_Count 0x0032 248 248 000 Old_age Always
- 2265
192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always
- 0
193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always
- 0
194 Temperature_Celsius 0x0032 253 253 000 Old_age Always
- 29
195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always
- 1546
196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline -
0
197 Current_Pending_Sector 0x0008 253 253 000 Old_age Offline -
0
198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline -
0
199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age Offline -
0
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always
- 0
201 Soft_Read_Error_Rate 0x000a 253 248 000 Old_age Always
- 2
202 TA_Increase_Count 0x000a 253 252 000 Old_age Always
- 0
203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always
- 0
204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always
- 0
205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always
- 0
207 Spin_High_Current 0x002a 253 246 000 Old_age Always
- 0
208 Spin_Buzz 0x002a 253 252 000 Old_age Always
- 0
209 Offline_Seek_Performnce 0x0024 201 199 000 Old_age Offline -
0
99 Unknown_Attribute 0x0004 253 253 000 Old_age Offline -
0
100 Unknown_Attribute 0x0004 253 253 000 Old_age Offline -
0
101 Unknown_Attribute 0x0004 253 253 000 Old_age Offline -
0
SMART Error Log Version: 1
Warning: ATA error count 11 inconsistent with error log pointer 5
ATA Error Count: 11 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 11 occurred at disk power-on lifetime: 13012 hours (542 days + 4 hours)
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 f0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 ff 01 00 00 00 f0 08 00:07:26.176 READ DMA
ef 03 46 b3 60 1f f0 08 00:07:26.176 SET FEATURES [Set transfer mode]
c6 ff 10 b3 60 1f f0 08 00:07:26.176 SET MULTIPLE MODE
10 ff 50 b3 60 1f f0 08 00:07:26.160 RECALIBRATE [OBS-4]
91 ff 3f 00 00 00 ff 08 00:07:26.160 INITIALIZE DEVICE PARAMETERS
[OBS-6]
Error 10 occurred at disk power-on lifetime: 13012 hours (542 days + 4 hours)
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 f0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 ff 01 00 00 00 f0 08 00:06:12.992 READ DMA
ef 03 46 fc e2 5d f0 08 00:06:12.992 SET FEATURES [Set transfer mode]
c6 ff 10 fc e2 5d f0 08 00:06:12.992 SET MULTIPLE MODE
10 ff 50 fc e2 5d f0 08 00:06:12.976 RECALIBRATE [OBS-4]
91 ff 3f 00 00 00 ff 08 00:06:12.976 INITIALIZE DEVICE PARAMETERS
[OBS-6]
Error 9 occurred at disk power-on lifetime: 13012 hours (542 days + 4 hours)
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 f0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 ff 01 00 00 00 f0 08 00:06:05.344 READ DMA
ef 03 46 05 26 db f0 08 00:06:05.344 SET FEATURES [Set transfer mode]
c6 ff 10 05 26 db f0 08 00:06:05.344 SET MULTIPLE MODE
10 ff 50 05 26 db f0 08 00:06:05.328 RECALIBRATE [OBS-4]
91 ff 3f 00 00 00 ff 08 00:06:05.328 INITIALIZE DEVICE PARAMETERS
[OBS-6]
Error 8 occurred at disk power-on lifetime: 13012 hours (542 days + 4 hours)
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 f0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 ff 01 00 00 00 f0 08 00:05:57.696 READ DMA
ef 03 46 0f e3 1e f0 08 00:05:57.696 SET FEATURES [Set transfer mode]
c6 ff 10 0f e3 1e f0 08 00:05:57.696 SET MULTIPLE MODE
10 ff 50 0f e3 1e f0 08 00:05:57.680 RECALIBRATE [OBS-4]
91 ff 3f 00 00 00 ff 08 00:05:57.680 INITIALIZE DEVICE PARAMETERS
[OBS-6]
Error 7 occurred at disk power-on lifetime: 13012 hours (542 days + 4 hours)
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 f0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 ff 01 00 00 00 f0 08 00:05:50.048 READ DMA
c6 03 10 3f fe 3f b0 08 00:05:47.872 SET MULTIPLE MODE
ef 03 46 3f fe 3f b0 08 00:05:47.872 SET FEATURES [Set transfer mode]
40 00 01 3f fe 3f bf 08 00:05:47.872 READ VERIFY SECTOR(S)
10 00 3f 3f 00 00 bf 08 00:05:47.856 RECALIBRATE [OBS-4]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Short captive Completed without error 00% 17564 -
# 2 Short captive Completed without error 00% 17214 -
# 3 Short captive Completed without error 00% 17199 -
# 4 Short captive Completed without error 00% 17198 -
# 5 Short offline Interrupted (host reset) 70% 2447 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
steven at Yesua:~$
Thanks either way.
Steven
More information about the kubuntu-users
mailing list