[Ubuntu-BR] Fwd: A luta continua (Modem ADSL USB, conecta, estabiliza ... mas não deixa navegar)
[<o>] Follmann
dlfollmann em gmail.com
Segunda Março 5 14:54:42 UTC 2007
Atento ao solicitado abaixo, aqui vai, de novo, a mensagem. Complementando,
a operadora é a BrT, Rio Grande do Sul. o Modem é um DSL D-210, da D-Link.
Tem posts meus no fórum do Ubuntu e do Guia do Hardware, li dezenas de
tutoriais, mas não resolvi o problema.
Obrigado pela disposição, "cara".
------------------------------
"Entao, amigo, qual o problema com seu modem ADSL? Tente descrever e vamos
tentar te ajudar ok? Descreve o maximo possivel, como marca do modem,
operadora,
etc.
--
Lucas Arruda
lucasarruda.com
-------------------------------
---------- Forwarded message ----------
From: [<o>] Follmann <dlfollmann em gmail.com>
Date: 25/02/2007 20:45
Subject: A luta continua (Modem ADSL USB, conecta, estabiliza ... mas não
deixa navegar)
To: Lista de discussão do LoCoTeam Brasileiro <ubuntu-br em lists.ubuntu.com>
Minha saga continua.
Formatei e fiz uma instalação limpa do Ubuntu (pela segunda vez). Como
(finalmente) percebi que o modem é reconhecido pelo Ubuntu, parei de tentar
instalar drivers de tutos antigos da rede. Mas continuo não conseguindo
fazer o PPPOECONF funcionar, nem criar a interface 'ppp0' (pontos comuns de
tudo o que li).
O interessante é que, olhando o resultado do DMESG (ver arquivo de mesmo
nome), dá pra ver que ele reconhece a linha, identificando corretamente a
velocidade. Ou seja, o SO sabe que o ADSL está ali, disponível. Quando
disparo o PPPOECONF, ele só acha a 'eth0'. Na tela onde isso acontece, diz
que, se há outra interface, devo dar ESC pra iniciar o MODCONF (ver arquivo
PPPOECONF_MODCONF). Mas na hora de carregar ele, só uma mensagem de erro.
Disparando o comando ROUTE, não aparece nada ( e isso antes de tentar dar o
'route del default', que tanto aparece nos tutos da rede)
Olhando o MODINFO, vejo também que o modem depende de algo chamado ATM. Isso
vem instalado por padrão ? O que é, pra que serve ?
Bom, tudo isso é pra pedir que algum dos membros da lista que seja mais
experimentado que eu em Ubuntu, Redes e ADSL (o que não é difícil) dê uma
olhadas nos logs que anexo, pra ver se acha o 'furo da bala'.
Não quiz incluir o texto dos anexos no corpo da mensagem, por dois motivos:
facilita a organização, se alguém quiser olhar, e evita que o texto fique
deveras extenso.
Perdão se vos torro a paciência, e mais uma vez agradeço a quem puder
ajudar. Se alguém estiver disposto a manter um diálogo mais direto, pode me
adicionar no messenger.
--
_________________________
[<o>] Dirceu Luís Follmann
MSN dlfollmann em gmail.com
--
_________________________
[<o>] Dirceu Luís Follmann
MSN dlfollmann em gmail.com
-------------- Próxima Parte ----------
[17179569.184000] Linux version 2.6.17-10-generic (root em vernadsky) (gcc version 4.1.2 20060928 (prerelease) (Ubuntu 4.1.1-13ubuntu5)) #2 SMP Fri Oct 13 18:45:35 UTC 2006 (Ubuntu 2.6.17-10.33-generic)
[17179569.184000] BIOS-provided physical RAM map:
[17179569.184000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[17179569.184000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[17179569.184000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[17179569.184000] BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
[17179569.184000] BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
[17179569.184000] BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
[17179569.184000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[17179569.184000] 0MB HIGHMEM available.
[17179569.184000] 511MB LOWMEM available.
[17179569.184000] found SMP MP-table at 000f4d80
[17179569.184000] On node 0 totalpages: 131056
[17179569.184000] DMA zone: 4096 pages, LIFO batch:0
[17179569.184000] Normal zone: 126960 pages, LIFO batch:31
[17179569.184000] DMI 2.3 present.
[17179569.184000] ACPI: RSDP (v000 GBT ) @ 0x000f6740
[17179569.184000] ACPI: RSDT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x1fff3000
[17179569.184000] ACPI: FADT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x1fff3040
[17179569.184000] ACPI: MADT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x1fff73c0
[17179569.184000] ACPI: DSDT (v001 GBT AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
[17179569.184000] ACPI: PM-Timer IO Port: 0x4008
[17179569.184000] ACPI: Local APIC address 0xfee00000
[17179569.184000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[17179569.184000] Processor #0 15:2 APIC version 20
[17179569.184000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
[17179569.184000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
[17179569.184000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[17179569.184000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[17179569.184000] IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
[17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[17179569.184000] ACPI: IRQ0 used by override.
[17179569.184000] ACPI: IRQ2 used by override.
[17179569.184000] ACPI: IRQ9 used by override.
[17179569.184000] Enabling APIC mode: Flat. Using 1 I/O APICs
[17179569.184000] Using ACPI (MADT) for SMP configuration information
[17179569.184000] Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
[17179569.184000] Built 1 zonelists
[17179569.184000] Kernel command line: root=/dev/hda7 ro quiet splash locale=pt_BR
[17179569.184000] mapped APIC to ffffd000 (fee00000)
[17179569.184000] mapped IOAPIC to ffffc000 (fec00000)
[17179569.184000] Enabling fast FPU save and restore... done.
[17179569.184000] Enabling unmasked SIMD FPU exception support... done.
[17179569.184000] Initializing CPU#0
[17179569.184000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[17179569.184000] Detected 2326.226 MHz processor.
[17179569.184000] Using pmtmr for high-res timesource
[17179569.184000] Console: colour VGA+ 80x25
[17179570.620000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[17179570.620000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[17179570.632000] Memory: 509800k/524224k available (1910k kernel code, 13836k reserved, 1070k data, 308k init, 0k highmem)
[17179570.632000] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[17179570.716000] Calibrating delay using timer specific routine.. 4658.15 BogoMIPS (lpj=9316310)
[17179570.716000] Security Framework v1.0.0 initialized
[17179570.716000] SELinux: Disabled at boot.
[17179570.716000] Mount-cache hash table entries: 512
[17179570.716000] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
[17179570.716000] CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
[17179570.716000] CPU: Trace cache: 12K uops, L1 D cache: 8K
[17179570.716000] CPU: L2 cache: 512K
[17179570.716000] CPU: Hyper-Threading is disabled
[17179570.716000] CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000
[17179570.716000] Checking 'hlt' instruction... OK.
[17179570.732000] SMP alternatives: switching to UP code
[17179570.732000] Freeing SMP alternatives: 16k freed
[17179570.732000] checking if image is initramfs... it is
[17179571.288000] Freeing initrd memory: 5563k freed
[17179571.288000] ACPI: Core revision 20060707
[17179571.292000] ACPI: Looking for DSDT ... not found!
[17179571.300000] CPU0: Intel(R) Pentium(R) 4 CPU 2.26GHz stepping 05
[17179571.300000] Total of 1 processors activated (4658.15 BogoMIPS).
[17179571.300000] ENABLING IO-APIC IRQs
[17179571.300000] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[17179571.444000] Brought up 1 CPUs
[17179571.444000] migration_cost=0
[17179571.444000] NET: Registered protocol family 16
[17179571.444000] EISA bus registered
[17179571.444000] ACPI: bus type pci registered
[17179571.444000] PCI: PCI BIOS revision 2.10 entry at 0xfa080, last bus=1
[17179571.444000] PCI: Using configuration type 1
[17179571.444000] Setting up standard PCI resources
[17179571.464000] ACPI: Interpreter enabled
[17179571.464000] ACPI: Using IOAPIC for interrupt routing
[17179571.464000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[17179571.464000] PCI: Probing PCI hardware (bus 00)
[17179571.468000] PCI: Ignoring BAR0-3 of IDE controller 0000:00:0f.0
[17179571.468000] PCI: Quirk-MSI-K8T Soundcard On
[17179571.468000] PCI: Unexpected Value in PCI-Register: no Change!
[17179571.468000] Boot video device is 0000:01:00.0
[17179571.468000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[17179571.496000] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 *11 12)
[17179571.496000] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 11 12) *5
[17179571.496000] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 *10 11 12)
[17179571.496000] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12) *0, disabled.
[17179571.496000] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled.
[17179571.500000] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled.
[17179571.500000] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled.
[17179571.500000] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled.
[17179571.500000] ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0, disabled.
[17179571.500000] ACPI: PCI Interrupt Link [ALKB] (IRQs 21) *0, disabled.
[17179571.500000] ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *0, disabled.
[17179571.500000] ACPI: PCI Interrupt Link [ALKD] (IRQs 23) *0, disabled.
[17179571.504000] Linux Plug and Play Support v0.97 (c) Adam Belay
[17179571.504000] pnp: PnP ACPI init
[17179571.508000] pnp: PnP ACPI: found 13 devices
[17179571.508000] PnPBIOS: Disabled by ACPI PNP
[17179571.508000] PCI: Using ACPI for IRQ routing
[17179571.508000] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[17179571.540000] pnp: 00:02: ioport range 0x4000-0x407f could not be reserved
[17179571.540000] pnp: 00:02: ioport range 0x40f0-0x40ff could not be reserved
[17179571.540000] pnp: 00:02: ioport range 0x5000-0x500f has been reserved
[17179571.540000] PCI: Bridge: 0000:00:01.0
[17179571.540000] IO window: disabled.
[17179571.540000] MEM window: ec000000-edffffff
[17179571.540000] PREFETCH window: e0000000-e7ffffff
[17179571.540000] PCI: Setting latency timer of device 0000:00:01.0 to 64
[17179571.540000] NET: Registered protocol family 2
[17179571.580000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[17179571.580000] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[17179571.580000] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[17179571.580000] TCP: Hash tables configured (established 16384 bind 8192)
[17179571.580000] TCP reno registered
[17179571.580000] audit: initializing netlink socket (disabled)
[17179571.580000] audit(1172428254.580:1): initialized
[17179571.580000] VFS: Disk quotas dquot_6.5.1
[17179571.580000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[17179571.580000] Initializing Cryptographic API
[17179571.580000] io scheduler noop registered
[17179571.580000] io scheduler anticipatory registered
[17179571.580000] io scheduler deadline registered
[17179571.580000] io scheduler cfq registered (default)
[17179571.580000] PCI: Bypassing VIA 8237 APIC De-Assert Message
[17179571.580000] isapnp: Scanning for PnP cards...
[17179571.936000] isapnp: No Plug & Play device found
[17179571.960000] Real Time Clock Driver v1.12ac
[17179571.960000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[17179571.960000] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179571.960000] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[17179571.964000] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179571.964000] 00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[17179571.964000] ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 18 (level, low) -> IRQ 169
[17179571.964000] 0000:00:06.0: ttyS2 at I/O 0xd008 (irq = 169) is a 16450
[17179571.964000] 0000:00:06.0: ttyS3 at I/O 0xd010 (irq = 169) is a 8250
[17179571.964000] Couldn't register serial port 0000:00:06.0: -28
[17179571.964000] mice: PS/2 mouse device common for all mice
[17179571.964000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[17179571.964000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[17179571.964000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[17179571.964000] PNP: PS/2 Controller [PNP0f13:PS2M] at 0x60,0x64 irq 12
[17179571.964000] PNP: PS/2 controller doesn't have KBD irq; using default 1
[17179571.964000] serio: i8042 AUX port at 0x60,0x64 irq 12
[17179571.964000] serio: i8042 KBD port at 0x60,0x64 irq 1
[17179571.964000] EISA: Probing bus 0 at eisa.0
[17179571.964000] Cannot allocate resource for EISA slot 4
[17179571.964000] Cannot allocate resource for EISA slot 5
[17179571.964000] EISA: Detected 0 cards.
[17179571.964000] TCP bic registered
[17179571.964000] NET: Registered protocol family 1
[17179571.964000] NET: Registered protocol family 8
[17179571.964000] NET: Registered protocol family 20
[17179571.964000] Using IPI No-Shortcut mode
[17179571.964000] ACPI: (supports S0 S3 S4 S5)
[17179571.968000] Freeing unused kernel memory: 308k freed
[17179573.112000] Capability LSM initialized
[17179573.152000] ACPI Exception (acpi_processor-0693): AE_NOT_FOUND, Processor Device is not present [20060707]
[17179573.152000] ACPI: Getting cpuindex for acpiid 0x1
[17179573.680000] VP_IDE: IDE controller at PCI slot 0000:00:0f.0
[17179573.680000] ACPI: PCI Interrupt Link [ALKA] BIOS reported IRQ 0, using IRQ 20
[17179573.680000] ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
[17179573.680000] ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 177
[17179573.680000] PCI: Via IRQ fixup for 0000:00:0f.0, from 255 to 1
[17179573.680000] VP_IDE: chipset revision 6
[17179573.680000] VP_IDE: not 100% native mode: will probe irqs later
[17179573.680000] VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.0
[17179573.680000] ide0: BM-DMA at 0xd400-0xd407, BIOS settings: hda:DMA, hdb:pio
[17179573.680000] ide1: BM-DMA at 0xd408-0xd40f, BIOS settings: hdc:pio, hdd:DMA
[17179573.680000] Probing IDE interface ide0...
[17179574.116000] hda: SAMSUNG SP1203N, ATA DISK drive
[17179574.792000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[17179574.800000] Probing IDE interface ide1...
[17179575.964000] hdd: HL-DT-ST RW/DVD GCC-4521B, ATAPI CD/DVD-ROM drive
[17179576.024000] ide1 at 0x170-0x177,0x376 on irq 15
[17179576.032000] hda: max request size: 512KiB
[17179576.040000] hda: 234493056 sectors (120060 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
[17179576.040000] hda: cache flushes supported
[17179576.040000] hda: hda1 hda2 < hda5 hda6 hda7 hda8 >
[17179576.124000] hdd: ATAPI 52X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
[17179576.124000] Uniform CD-ROM driver Revision: 3.20
[17179576.432000] usbcore: registered new driver usbfs
[17179576.432000] usbcore: registered new driver hub
[17179576.432000] USB Universal Host Controller Interface driver v3.0
[17179576.432000] ACPI: PCI Interrupt Link [ALKB] BIOS reported IRQ 0, using IRQ 21
[17179576.432000] ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
[17179576.432000] ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 185
[17179576.432000] PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 9
[17179576.432000] uhci_hcd 0000:00:10.0: UHCI Host Controller
[17179576.432000] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
[17179576.432000] uhci_hcd 0000:00:10.0: irq 185, io base 0x0000d800
[17179576.432000] usb usb1: configuration #1 chosen from 1 choice
[17179576.432000] hub 1-0:1.0: USB hub found
[17179576.432000] hub 1-0:1.0: 2 ports detected
[17179576.540000] ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 185
[17179576.540000] PCI: Via IRQ fixup for 0000:00:10.1, from 11 to 9
[17179576.540000] uhci_hcd 0000:00:10.1: UHCI Host Controller
[17179576.540000] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
[17179576.540000] uhci_hcd 0000:00:10.1: irq 185, io base 0x0000dc00
[17179576.540000] usb usb2: configuration #1 chosen from 1 choice
[17179576.540000] hub 2-0:1.0: USB hub found
[17179576.540000] hub 2-0:1.0: 2 ports detected
[17179576.648000] ACPI: PCI Interrupt 0000:00:10.2[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 185
[17179576.648000] PCI: Via IRQ fixup for 0000:00:10.2, from 5 to 9
[17179576.648000] uhci_hcd 0000:00:10.2: UHCI Host Controller
[17179576.648000] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
[17179576.648000] uhci_hcd 0000:00:10.2: irq 185, io base 0x0000e000
[17179576.648000] usb usb3: configuration #1 chosen from 1 choice
[17179576.648000] hub 3-0:1.0: USB hub found
[17179576.648000] hub 3-0:1.0: 2 ports detected
[17179576.764000] ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 185
[17179576.764000] PCI: Via IRQ fixup for 0000:00:10.4, from 10 to 9
[17179576.764000] ehci_hcd 0000:00:10.4: EHCI Host Controller
[17179576.764000] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 4
[17179576.764000] ehci_hcd 0000:00:10.4: irq 185, io mem 0xee001000
[17179576.764000] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[17179576.764000] usb usb4: configuration #1 chosen from 1 choice
[17179576.764000] hub 4-0:1.0: USB hub found
[17179576.764000] hub 4-0:1.0: 6 ports detected
[17179576.780000] usb 1-1: new full speed USB device using uhci_hcd and address 2
[17179576.928000] Attempting manual resume
[17179576.956000] kjournald starting. Commit interval 5 seconds
[17179576.960000] EXT3-fs: mounted filesystem with ordered data mode.
[17179578.292000] usb 3-1: new low speed USB device using uhci_hcd and address 2
[17179578.484000] usb 3-1: configuration #1 chosen from 1 choice
[17179578.724000] usb 1-1: new full speed USB device using uhci_hcd and address 3
[17179578.912000] usb 1-1: configuration #1 chosen from 1 choice
[17179578.912000] hub 1-1:1.0: USB hub found
[17179578.916000] hub 1-1:1.0: 2 ports detected
[17179579.264000] usb 1-2: new full speed USB device using uhci_hcd and address 4
[17179579.456000] usb 1-2: configuration #1 chosen from 1 choice
[17179579.688000] usb 1-1.1: new full speed USB device using uhci_hcd and address 5
[17179579.840000] usb 1-1.1: configuration #1 chosen from 1 choice
[17179580.076000] usb 1-1.2: new full speed USB device using uhci_hcd and address 6
[17179580.228000] usb 1-1.2: configuration #1 chosen from 1 choice
[17179586.776000] Floppy drive(s): fd0 is 1.44M
[17179586.800000] FDC 0 is a post-1991 82077
[17179586.900000] via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
[17179586.900000] ACPI: PCI Interrupt Link [ALKD] BIOS reported IRQ 0, using IRQ 23
[17179586.900000] ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23
[17179586.900000] ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [ALKD] -> GSI 23 (level, low) -> IRQ 193
[17179586.900000] PCI: Via IRQ fixup for 0000:00:12.0, from 11 to 1
[17179586.904000] eth0: VIA Rhine II at 0x1e800, 00:0f:ea:9a:0c:d7, IRQ 193.
[17179586.904000] eth0: MII PHY found at address 1, status 0x7849 advertising 01e1 Link 0000.
[17179587.320000] parport: PnPBIOS parport detected.
[17179587.320000] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[17179587.740000] eth0: link down
[17179587.756000] Linux agpgart interface v0.101 (c) Dave Jones
[17179587.760000] agpgart: Detected VIA P4M266x/P4N266 chipset
[17179587.764000] agpgart: AGP aperture is 64M @ 0xe8000000
[17179587.836000] drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 6 if 0 alt 0 proto 2 vid 0x043D pid 0x007B
[17179587.836000] usbcore: registered new driver usblp
[17179587.836000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[17179587.904000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[17179587.908000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[17179587.940000] usbcore: registered new driver cxacru
[17179587.940000] usbcore: registered new driver hiddev
[17179587.956000] input: PC Speaker as /class/input/input0
[17179587.976000] input: GBE INC. Wireless Keyboard & Mouse as /class/input/input1
[17179587.976000] input: USB HID v1.10 Keyboard [GBE INC. Wireless Keyboard & Mouse] on usb-0000:00:10.2-1
[17179588.036000] input: GBE INC. Wireless Keyboard & Mouse as /class/input/input2
[17179588.040000] input,hiddev96: USB HID v1.10 Mouse [GBE INC. Wireless Keyboard & Mouse] on usb-0000:00:10.2-1
[17179588.040000] usbcore: registered new driver usbhid
[17179588.040000] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[17179588.252000] ACPI: PCI Interrupt Link [ALKC] BIOS reported IRQ 0, using IRQ 22
[17179588.252000] ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
[17179588.252000] ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [ALKC] -> GSI 22 (level, low) -> IRQ 201
[17179588.252000] PCI: Via IRQ fixup for 0000:00:11.5, from 10 to 9
[17179588.252000] PCI: Setting latency timer of device 0000:00:11.5 to 64
[17179588.356000] ts: Compaq touchscreen protocol output
[17179588.596000] input: ImPS/2 Generic Wheel Mouse as /class/input/input3
[17179588.780000] NET: Registered protocol family 17
[17179589.184000] lp0: using parport0 (interrupt-driven).
[17179589.220000] Adding 530104k swap on /dev/disk/by-uuid/846124ce-1bd9-4655-994a-3abd3786eac8. Priority:-1 extents:1 across:530104k
[17179589.336000] EXT3 FS on hda7, internal journal
[17179589.628000] NTFS driver 2.1.27 [Flags: R/O MODULE].
[17179589.676000] NTFS volume version 3.1.
[17179589.716000] NTFS volume version 3.1.
[17179589.736000] kjournald starting. Commit interval 5 seconds
[17179589.736000] EXT3 FS on hda8, internal journal
[17179589.736000] EXT3-fs: mounted filesystem with ordered data mode.
[17179595.292000] ACPI: Power Button (FF) [PWRF]
[17179595.292000] ACPI: Power Button (CM) [PWRB]
[17179595.428000] ibm_acpi: ec object not found
[17179595.460000] pcc_acpi: loading...
[17179597.968000] ATM dev 0: ADSL line: attempting to activate
[17179598.528000] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[17179598.528000] apm: overridden by ACPI.
[17179604.912000] Bluetooth: Core ver 2.8
[17179604.912000] NET: Registered protocol family 31
[17179604.912000] Bluetooth: HCI device and connection manager initialized
[17179604.912000] Bluetooth: HCI socket layer initialized
[17179604.932000] Bluetooth: L2CAP ver 2.8
[17179604.932000] Bluetooth: L2CAP socket layer initialized
[17179604.948000] Bluetooth: RFCOMM socket layer initialized
[17179604.948000] Bluetooth: RFCOMM TTY layer initialized
[17179604.948000] Bluetooth: RFCOMM ver 1.7
[17179612.124000] NET: Registered protocol family 10
[17179612.124000] lo: Disabled Privacy Extensions
[17179612.124000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[17179612.124000] IPv6 over IPv4 tunneling driver
[17179613.024000] ATM dev 0: ADSL line: down
[17179623.052000] ATM dev 0: ADSL line: attempting to activate
[17179633.080000] ATM dev 0: ADSL line: channel analysis
[17179638.100000] ATM dev 0: ADSL line: up (256 kb/s down | 128 kb/s up)
[17180705.028000] CSLIP: code copyright 1989 Regents of the University of California
[17180705.048000] PPP generic driver version 2.4.2
[17180705.056000] NET: Registered protocol family 24
-------------- Próxima Parte ----------
???eth0 Encapsulamento do Link: Ethernet Endere??o de HW 00:0F:EA:9A:0C:D7
UP BROADCAST MULTICAST MTU:1500 M??trica:1
pacotes RX:0 erros:0 descartados:0 excesso:0 quadro:0
Pacotes TX:0 erros:0 descartados:0 excesso:0 portadora:0
colis??es:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
IRQ:193 Endere??o de E/S:0xe800
lo Encapsulamento do Link: Loopback Local
inet end.: 127.0.0.1 Masc:255.0.0.0
endere??o inet6: ::1/128 Escopo:M??quina
UP LOOPBACK RUNNING MTU:16436 M??trica:1
pacotes RX:74 erros:0 descartados:0 excesso:0 quadro:0
Pacotes TX:74 erros:0 descartados:0 excesso:0 portadora:0
colis??es:0 txqueuelen:0
RX bytes:5540 (5.4 KiB) TX bytes:5540 (5.4 KiB)
sit0 Encapsulamento do Link: IPv6 sobre IPv4
NOARP MTU:1480 M??trica:1
pacotes RX:0 erros:0 descartados:0 excesso:0 quadro:0
Pacotes TX:0 erros:0 descartados:0 excesso:0 portadora:0
colis??es:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
-------------- Próxima Parte ----------
Module Size Used by
pppoe 16064 0
pppox 4872 1 pppoe
ppp_generic 30612 2 pppoe,pppox
slhc 8448 1 ppp_generic
ipv6 272288 8
binfmt_misc 13448 1
rfcomm 42260 0
l2cap 27136 5 rfcomm
bluetooth 53476 4 rfcomm,l2cap
speedstep_lib 5764 0
cpufreq_userspace 5408 0
cpufreq_stats 7744 0
freq_table 6048 1 cpufreq_stats
cpufreq_powersave 2944 0
cpufreq_ondemand 8876 0
cpufreq_conservative 8712 0
video 17540 0
tc1100_wmi 8324 0
sony_acpi 6412 0
sbs 16804 0
pcc_acpi 14080 0
i2c_ec 6272 1 sbs
hotkey 11556 0
dev_acpi 12292 0
container 5632 0
button 7952 0
battery 11652 0
asus_acpi 17688 0
ac 6788 0
nls_utf8 3200 2
ntfs 112116 2
lp 12964 0
snd_seq_dummy 4996 0
snd_seq_oss 36480 0
snd_seq_midi 9984 0
snd_seq_midi_event 8960 2 snd_seq_oss,snd_seq_midi
snd_seq 59120 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
af_packet 24584 2
tsdev 9152 0
snd_via82xx 30360 1
gameport 17160 1 snd_via82xx
snd_ac97_codec 97696 1 snd_via82xx
snd_ac97_bus 3456 1 snd_ac97_codec
snd_pcm_oss 47360 0
snd_mixer_oss 19584 1 snd_pcm_oss
snd_pcm 84612 3 snd_via82xx,snd_ac97_codec,snd_pcm_oss
snd_timer 25348 2 snd_seq,snd_pcm
snd_page_alloc 11400 2 snd_via82xx,snd_pcm
snd_mpu401_uart 10240 1 snd_via82xx
snd_rawmidi 27264 2 snd_seq_midi,snd_mpu401_uart
snd_seq_device 9868 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq,snd_rawmidi
snd 58372 13 snd_seq_oss,snd_seq,snd_via82xx,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device
pcspkr 4352 0
psmouse 41352 0
serio_raw 8452 0
shpchp 42144 0
pci_hotplug 32828 1 shpchp
usbhid 45152 0
cxacru 13696 0
usbatm 20864 1 cxacru
i2c_viapro 9876 0
usblp 15488 0
i2c_core 23424 2 i2c_ec,i2c_viapro
soundcore 11232 1 snd
via_agp 11264 1
agpgart 34888 1 via_agp
evdev 11392 2
parport_pc 37796 1
parport 39496 2 lp,parport_pc
via_rhine 26116 0
mii 6912 1 via_rhine
floppy 63044 0
ext3 142728 2
jbd 62228 1 ext3
ehci_hcd 34696 0
uhci_hcd 24968 0
usbcore 134912 7 usbhid,cxacru,usbatm,usblp,ehci_hcd,uhci_hcd
ide_generic 2432 0
ide_cd 33696 0
cdrom 38944 1 ide_cd
ide_disk 18560 6
via82cxxx 10500 0 [permanent]
generic 5764 0
thermal 15624 0
processor 31560 1 thermal
fan 6020 0
fbcon 41504 0
tileblit 3840 1 fbcon
font 9344 1 fbcon
bitblit 7168 1 fbcon
softcursor 3328 1 bitblit
vesafb 9244 0
capability 5896 0
commoncap 8704 1 capability
-------------- Próxima Parte ----------
00:00.0 Host bridge: VIA Technologies, Inc. P4M266 Host Bridge
00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP]
00:06.0 Modem: PCTel Inc HSP56 MicroModem (rev 04)
00:0f.0 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South]
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 78)
01:00.0 VGA compatible controller: nVidia Corporation NV34 [GeForce FX 5200] (rev a1)
-------------- Próxima Parte ----------
Bus 004 Device 001: ID 0000:0000
Bus 003 Device 002: ID 0b38:0002
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 004: ID 0572:cb00 Conexant Systems (Rockwell), Inc. E-Tech ADSL Modem v2
Bus 001 Device 006: ID 043d:007b Lexmark International, Inc.
Bus 001 Device 003: ID 043d:007a Lexmark International, Inc.
Bus 001 Device 005: ID 043d:007c Lexmark International, Inc.
Bus 001 Device 001: ID 0000:0000
-------------- Próxima Parte ----------
ubuntu em desk:/sbin$ modinfo cxacru
filename: /lib/modules/2.6.17-10-generic/kernel/drivers/usb/atm/cxacru.ko
author: Roman Kagan, David Woodhouse, Duncan Sands
description: Conexant AccessRunner ADSL USB modem driver
license: GPL
version: 0.2
vermagic: 2.6.17-10-generic SMP mod_unload 586 REGPARM gcc-4.1
depends: usbatm,usbcore
alias: usb:v0572pCAFEd*dc*dsc*dp*ic*isc*ip*
alias: usb:v0572pCB00d*dc*dsc*dp*ic*isc*ip*
alias: usb:v0572pCB01d*dc*dsc*dp*ic*isc*ip*
alias: usb:v0572pCB02d*dc*dsc*dp*ic*isc*ip*
alias: usb:v0572pCB06d*dc*dsc*dp*ic*isc*ip*
alias: usb:v08E3p0100d*dc*dsc*dp*ic*isc*ip*
alias: usb:v08E3p0102d*dc*dsc*dp*ic*isc*ip*
alias: usb:v0EB0p3457d*dc*dsc*dp*ic*isc*ip*
alias: usb:v1803p5510d*dc*dsc*dp*ic*isc*ip*
alias: usb:v0675p0200d*dc*dsc*dp*ic*isc*ip*
alias: usb:v0586p330Ad*dc*dsc*dp*ic*isc*ip*
alias: usb:v0586p330Bd*dc*dsc*dp*ic*isc*ip*
alias: usb:v0659p0020d*dc*dsc*dp*ic*isc*ip*
alias: usb:v0509p0812d*dc*dsc*dp*ic*isc*ip*
alias: usb:v100DpCB01d*dc*dsc*dp*ic*isc*ip*
alias: usb:v100Dp3342d*dc*dsc*dp*ic*isc*ip*
srcversion: DA75A46E3C52B921637447E
-------------- Próxima Parte ----------
ubuntu em desk:~$ sudo pppoeconf
/usr/sbin/pppoeconf: 447: modconf: not found
-------------- Próxima Parte ----------
???ubuntu em desk:~$ sudo route del default
Password:
SIOCDELRT: N??o existe o processo
ubuntu em desk:~$ sudo route add default ppp0
SIOCADDRT: N??o h?? tal dispositivo
ubuntu em desk:~$ sudo route add default ppp1
SIOCADDRT: N??o h?? tal dispositivo
ubuntu em desk:~$ sudo route add default nas0
SIOCADDRT: N??o h?? tal dispositivo
ubuntu em desk:~$
ubuntu em desk:~$ sudo route
Tabela de Roteamento IP do Kernel
Destino Roteador M??scaraGen. Op????es M??trica Ref Uso Iface
More information about the ubuntu-br
mailing list