Speedtouch 350 und Echolinux

[Frank]

doch ich sende Dir mal das Fehlerprotokoll, habe ev. ein gebrauchtes Modem 
> ich habe ein Speedtouch 510, bei diesem und wie es scheint auch bei
> Deinem Modem, ist per Werkeinstellung kein Kennwort vergeben. Sollte
> aus irgendwelchen Gründen doch eines vorhanden sein, sollte es durch
> einen Reset, !!! wie leider auch der Rest der Konfiguration !!!,
> wieder leer sein. Die Info zum Einstellen eines neuen Kennwortes
> befindet sich in der Doku. Seite 26
alles gelesen bringt nix

>
> Gruß Ralf

-- 
Mit einem beherzten Ubuntu-Linux Gruß
Frank
Ammerlaender Trinkspruch
Gastgeber "Ick seh Di." Gast "Dat freit mi." 
Gastgeber "Ick sup Di to" Gast "Dat do." 
Prost Gastgeber "Ick hev Di tosapen." 
Gast: "Hest'n Recht'n drapen" 

This message was sent using 100 % recycled electrons

Irgendwie macht Microsoft die User zu Hausfrauen. -- Spätestens nach
nem halben Jahr müssen die das nochmal "drüberbügeln".
(aus Ubuntu - Liste Goran Ristic)

www.enfield-zeitschrift.de/download.html

www.oyla9.de/cgi-bin/hpm_homepage.cgi?skip=28357454

UBUNTU LINUX Breezy 5.10
http://counter.li.org Registered User #401478

-------------- nächster Teil --------------
EchoLink Troubleshooter ver 1.2.0.5
Diagnostic Report for DK8ZF
Prepared Saturday, January 21, 2006 13:43:54 Westeuropäische Normalzeit



*** User Information ***

Callsign: DK8ZF


*** System Information ***

Windows XP Service Pack 1


*** Network Options ***

Shared Internet Connection: No
Wireless: No


*** Security Software Configuration ***

Auto-detected the following security software on your computer:

Zone Labs ZoneAlarm version 6.1.737.000

You indicated that the following security software is installed:
   Zone Labs ZoneAlarm


*** Network Configuration ***

Local IP Address: 10.0.0.50
This is a local address that is not directly reachable from the Internet.  This usually indicates that your system is using a network address translation (NAT) device, such as a router, as part of your Internet connnection.  This is a perfectly normal indication; however, it often means that your firewall or router needs special settings to work correctly with EchoLink.  The tests below will confirm this.

Connection type: Digital Subscriber Line (DSL)
Shared Internet connection: No
Wireless network connection: No


*** TCP Connectivity Test ***

The TCP test SUCCEEDED.
This means that EchoLink should be able to successfully log in to the EchoLink addressing servers and retrieve the list of stations.  No further adjustments to your TCP settings should be required.

The UDP port 5198 test FAILED: Receive failed (10060).
This means that EchoLink cannot communicate with other stations over the Internet.  Be sure your router, firewall, or security software is allowing EchoLink to receive messages over UDP ports 5198 and 5199, and that your Internet service provider (ISP) has not blocked this port.

Things to check:

* Some DSL modems have a built-in firewall that must be configured to accept UDP ports 5198 and 5199.  Check the modem's documentation, or your DSL provider's customer support, for more information.

* Check your ZoneAlarm documentation for information about how to permit your PC to receive UDP ports 5198 and 5199.  If you are using the free version of ZoneAlarm, you must set the security level to Medium while you are using EchoLink.  Other versions of ZoneAlarm have advanced settings that allow UDP ports 5198 and 5199 to be accepted, while still in High security mode (recommended).

* If you had used the "Program" or "Server" security settings in your security software, and began having connection problems after upgrading EchoLink, you may need to re-apply your previous security settings.  You might also need to apply the same settings to the Troubleshooter program (this program) in order for it to work correctly.

* A few Internet service providers (ISPs) block a range of different UDP ports, including ports 5198 and 5199 used by EchoLink.  Although this is relatively rare, check with your ISP if the rest of your configuration appears to be OK.


*** Sound Configuration ***

Available Input Device(s): 
   Avance AC97 Audio
Available Output Device(s): 
   Avance AC97 Audio
Selected Input device: Avance AC97 Audio
Selected Output device: Avance AC97 Audio
Full duplex: Yes
Name of Microphone slider: "Mikrofon"
Name of Line In slider: ""
Audio input connected to: Mikrofon

The current settings of each of your Windows sound controls are shown below.  Note that some of these controls may not be visible on the Volume Control panel, depending on the setting of your Volume Control panel options.

Recording Controls:

              Mono Mix: Level =   7;  Muted =  No;  Selected = Yes
            Stereo Mix: Level =   7;  Muted =  No;  Selected =  No
             CD-Player: Level = 100;  Muted =  No;  Selected =  No
              Mikrofon: Level =  85;  Muted =  No;  Selected =  No

Playback Controls:

     Speakers (Master): Level = 100;  Muted =  No
                  Wave: Level = 100;  Muted =  No
        SW-Synthesizer: Level =  98;  Muted =  No
                 SPDIF: Level =  50;  Muted =  No
             CD-Player: Level = 100;  Muted =  No
              Mikrofon: Level = 100;  Muted =  No
       PC-Lautsprecher: Level = 100;  Muted =  No

NOTE: You are using the Mikrofon input jack, but the Mikrofon volume is turned down, muted, or not selected on your Windows Recording volume controls.  Check and adjust the Mikrofon setting on your Windows RECORDING Volume Controls (NOT the Playback volume controls).

NOTE: One or more sources other than "Mikrofon" are turned up on the Recording volume control.  This may introduce stray audio.  Check and adjust the following controls (on the RECORDING volume control panel):
    Mono Mix


NOTE: The Microphone volume control appears to be turned up on the Playback volume control panel.  This may cause undesirable feedback, if you are using a local microphone, and is not necessary for EchoLink operation.  Check and adjust the microphone control (on the PLAYBACK volume control panel).

NOTE: There appear to be some Advanced settings available for the Mikrofon control on the Recording volume control panel.  You can check these settings by opening the Recording volume control panel and enabling Advanced Controls from the Options menu.  The advanced controls are:
    Mic Boost
    
*** Support Resources ***

If you still need help configuring your system, here are some Web sites that may be useful:

ZoneAlarm Help: http://www.zonelabs.com/store/content/support/znalmMain.jsp

Microsoft Support: http://support.microsoft.com

Microsoft Windows Update: http://windowsupdate.microsoft.com

EchoLink Firewall Solutions: http://www.echolink.org/firewall_solutions.htm

EchoLink Support: http://www.echolink.org/support.htm

*** END OF REPORT ***