Re: problemas con la red inalámbrica
Manuel Grau Aracil
invocationtargetexception en gmail.com
Jue Mar 23 20:35:33 GMT 2006
Te mando la salida de todos los comandos que me has dicho, aunque ahora
mismo internet me funciona:
mgrau en grimgroth:~$ sudo iwconfig ra0
ra0 RT2500 Wireless ESSID:"casa"
Mode:Managed Frequency=2.472 GHz Access Point: 00:14:BF:62:98:A2
Bit Rate:36 Mb/s
RTS thr:off Fragment thr:off
Encryption key:off
Link Quality=61/100 Signal level=-63 dBm Noise level:-193 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
mgrau en grimgroth:~$ sudo dhclient ra0
Internet Systems Consortium DHCP Client V3.0.2
Copyright 2004 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/products/DHCP
sit0: unknown hardware address type 776
sit0: unknown hardware address type 776
Listening on LPF/ra0/00:80:5a:32:cb:ba
Sending on LPF/ra0/00:80:5a:32:cb:ba
Sending on Socket/fallback
DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 8
DHCPOFFER from 192.168.1.1
DHCPREQUEST on ra0 to 255.255.255.255 port 67
DHCPACK from 192.168.1.1
bound to 192.168.1.102 -- renewal in 32662 seconds.
mgrau en grimgroth:~$ dmesg
p6 > p3 p4
[4294675.267000] hdc: ATAPI 40X DVD-ROM drive, 256kB Cache
[4294675.267000] Uniform CD-ROM driver Revision: 3.20
[4294675.269000] hdd: ATAPI 44X CD-ROM CD-R/RW drive, 8192kB Cache
[4294675.919000] Attempting manual resume
[4294675.935000] swsusp: Suspend partition has wrong signature?
[4294676.012000] usbcore: registered new driver usbfs
[4294676.012000] usbcore: registered new driver hub
[4294676.014000] USB Universal Host Controller Interface driver v2.2
[4294676.015000] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
[4294676.015000] PCI: setting IRQ 10 as level-triggered
[4294676.015000] ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI
10 (level, low) -> IRQ 10
[4294676.015000] PCI: Via IRQ fixup for 0000:00:07.2, from 11 to 10
[4294676.015000] uhci_hcd 0000:00:07.2: VIA Technologies, Inc. VT82xxxxx
UHCI USB 1.1 Controller
[4294676.077000] uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus
number 1
[4294676.077000] uhci_hcd 0000:00:07.2: irq 10, io base 0x0000d400
[4294676.077000] hub 1-0:1.0: USB hub found
[4294676.077000] hub 1-0:1.0: 2 ports detected
[4294676.080000] ACPI: PCI Interrupt 0000:00:07.3[D] -> Link [LNKD] -> GSI
10 (level, low) -> IRQ 10
[4294676.080000] PCI: Via IRQ fixup for 0000:00:07.3, from 11 to 10
[4294676.080000] uhci_hcd 0000:00:07.3: VIA Technologies, Inc. VT82xxxxx
UHCI USB 1.1 Controller (#2)
[4294676.142000] uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus
number 2
[4294676.142000] uhci_hcd 0000:00:07.3: irq 10, io base 0x0000d800
[4294676.142000] hub 2-0:1.0: USB hub found
[4294676.142000] hub 2-0:1.0: 2 ports detected
[4294676.190000] 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
[4294676.190000] 8139cp: pci dev 0000:00:08.0 (id 10ec:8139 rev 10) is not
an 8139C+ compatible chip
[4294676.190000] 8139cp: Try the "8139too" driver instead.
[4294676.193000] 8139too Fast Ethernet driver 0.9.27
[4294676.193000] ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKD] -> GSI
10 (level, low) -> IRQ 10
[4294676.194000] eth0: RealTek RTL8139 at 0xdc00, 00:c0:df:0a:ae:04, IRQ 10
[4294676.194000] eth0: Identified 8139 chip type 'RTL-8139C'
[4294676.246000] usb 1-1: new full speed USB device using uhci_hcd and
address 2
[4294679.101000] ACPI: CPU0 (power states: C1[C1] C2[C2])
[4294679.101000] ACPI: Processor [CPU0] (supports 2 throttling states)
[4294679.388000] Attempting manual resume
[4294679.413000] swsusp: Suspend partition has wrong signature?
[4294679.451000] kjournald starting. Commit interval 5 seconds
[4294679.451000] EXT3-fs: mounted filesystem with ordered data mode.
[4294680.639000] md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
[4294684.974000] Adding 779144k swap on /dev/hda5. Priority:-1 extents:1
[4294685.193000] EXT3 FS on hda3, internal journal
[4294697.947000] parport_pc: VIA 686A/8231 detected
[4294697.947000] parport_pc: probing current configuration
[4294697.947000] parport_pc: Current parallel port base: 0x0
[4294697.947000] parport_pc: VIA parallel port disabled in BIOS
[4294697.952000] lp: driver loaded but no devices found
[4294697.978000] mice: PS/2 mouse device common for all mice
[4294698.191000] logips2pp: Detected unknown logitech mouse model 56
[4294698.193000] device-mapper: 4.4.0-ioctl (2005-01-12) initialised:
dm-devel en redhat.com
[4294698.307000] input: ImExPS/2 Logitech Explorer Mouse on isa0060/serio1
[4294698.699000] ts: Compaq touchscreen protocol output
[4294700.730000] cdrom: open failed.
[4294700.731000] cdrom: open failed.
[4294701.056000] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error
}
[4294701.056000] hda: dma_intr: error=0x10 { SectorIdNotFound },
LBAsect=78165360, sector=78165360
[4294701.056000] ide: failed opcode was: unknown
[4294701.198000] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error
}
[4294701.198000] hda: dma_intr: error=0x10 { SectorIdNotFound },
LBAsect=78165360, sector=78165360
[4294701.198000] ide: failed opcode was: unknown
[4294701.341000] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error
}
[4294701.341000] hda: dma_intr: error=0x10 { SectorIdNotFound },
LBAsect=78165360, sector=78165360
[4294701.341000] ide: failed opcode was: unknown
[4294701.483000] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error
}
[4294701.483000] hda: dma_intr: error=0x10 { SectorIdNotFound },
LBAsect=78165360, sector=78165360
[4294701.483000] ide: failed opcode was: unknown
[4294701.483000] hda: DMA disabled
[4294701.533000] ide0: reset: success
[4294701.707000] hda: task_in_intr: status=0x59 { DriveReady SeekComplete
DataRequest Error }
[4294701.707000] hda: task_in_intr: error=0x10 { SectorIdNotFound },
LBAsect=78230639, sector=78165360
[4294701.707000] ide: failed opcode was: unknown
[4294701.882000] hda: task_in_intr: status=0x59 { DriveReady SeekComplete
DataRequest Error }
[4294701.882000] hda: task_in_intr: error=0x10 { SectorIdNotFound },
LBAsect=78230639, sector=78165360
[4294701.882000] ide: failed opcode was: unknown
[4294702.057000] hda: task_in_intr: status=0x59 { DriveReady SeekComplete
DataRequest Error }
[4294702.057000] hda: task_in_intr: error=0x10 { SectorIdNotFound },
LBAsect=78230639, sector=78165360
[4294702.057000] ide: failed opcode was: unknown
[4294702.231000] hda: task_in_intr: status=0x59 { DriveReady SeekComplete
DataRequest Error }
[4294702.232000] hda: task_in_intr: error=0x10 { SectorIdNotFound },
LBAsect=78230639, sector=78165360
[4294702.232000] ide: failed opcode was: unknown
[4294702.282000] ide0: reset: success
[4294702.456000] hda: task_in_intr: status=0x59 { DriveReady SeekComplete
DataRequest Error }
[4294702.456000] hda: task_in_intr: error=0x10 { SectorIdNotFound },
LBAsect=78230639, sector=78165360
[4294702.456000] ide: failed opcode was: unknown
[4294702.457000] end_request: I/O error, dev hda, sector 78165360
[4294704.443000] kjournald starting. Commit interval 5 seconds
[4294704.444000] EXT3 FS on hda4, internal journal
[4294704.444000] EXT3-fs: mounted filesystem with ordered data mode.
[4294704.460000] NTFS driver 2.1.22 [Flags: R/O MODULE].
[4294704.579000] NTFS volume version 3.1.
[4294704.594000] kjournald starting. Commit interval 5 seconds
[4294704.595000] EXT3 FS on hda6, internal journal
[4294704.595000] EXT3-fs: mounted filesystem with ordered data mode.
[4294707.098000] Linux agpgart interface v0.101 (c) Dave Jones
[4294707.119000] agpgart: Detected VIA Twister-K/KT133x/KM133 chipset
[4294707.145000] agpgart: AGP aperture is 128M @ 0xd0000000
[4294708.694000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[4294708.707000] shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
[4294708.707000] shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
[4294711.310000] ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKD] -> GSI
10 (level, low) -> IRQ 10
[4294713.368000] gameport: EMU10K1 is pci0000:00:09.1/gameport0, io 0xe400,
speed 1242kHz
[4294714.019000] Linux video capture interface: v1.00
[4294714.094000] bttv: driver version 0.9.15 loaded
[4294714.094000] bttv: using 8 buffers with 2080k (520 pages) each for
capture
[4294714.103000] bttv: Bt8xx card found (0).
[4294714.104000] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 7
[4294714.104000] PCI: setting IRQ 7 as level-triggered
[4294714.104000] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKB] -> GSI 7
(level, low) -> IRQ 7
[4294714.104000] bttv0: Bt878 (rev 17) at 0000:00:0b.0, irq: 7, latency: 32,
mmio: 0xea002000
[4294714.104000] bttv0: detected: Pinnacle PCTV [card=39], PCI subsystem ID
is 11bd:0012
[4294714.104000] bttv0: using: Pinnacle PCTV Studio/Rave
[card=39,autodetected]
[4294714.104000] bttv0: gpio: en=00000000, out=00000000 in=00fffbdf [init]
[4294714.147000] bttv0: i2c: checking for MSP34xx @ 0x80... found
[4294714.148000] bttv0: pinnacle/mt: id=2 info="PAL+SECAM / stereo"
radio=yes
[4294714.148000] bttv0: using tuner=33
[4294714.148000] bttv0: i2c: checking for MSP34xx @ 0x80... found
[4294714.203000] msp34xx: init: chip=MSP3410G-B11 +nicam +simple +simpler
+radio mode=simpler
[4294714.237000] msp34xxg: daemon started
[4294714.305000] bttv0: i2c: checking for TDA9875 @ 0xb0... not found
[4294714.307000] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
[4294714.334000] tda9885/6/7: chip found @ 0x86
[4294714.404000] tuner 1-0060: chip found @ 0xc0 (bt878 #0 [sw])
[4294714.413000] tuner 1-0060: microtune: companycode=4d54 part=04 rev=04
[4294714.470000] tuner 1-0060: microtune MT2032 found, OK
[4294714.544000] bttv0: registered device video0
[4294714.546000] bttv0: registered device vbi0
[4294714.548000] bttv0: registered device radio0
[4294714.616000] bttv0: PLL: 28636363 => 35468950 .. ok
[4294715.742000] bt878: AUDIO driver version 0.0.0 loaded
[4294715.752000] bt878: Bt878 AUDIO function found (0).
[4294715.752000] ACPI: PCI Interrupt 0000:00:0b.1[A] -> Link [LNKB] -> GSI 7
(level, low) -> IRQ 7
[4294715.752000] bt878(0): Bt878 (rev 17) at 00:0b.1, irq: 7, latency: 32,
memory: 0xea003000
[4294715.964000] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5
[4294715.964000] PCI: setting IRQ 5 as level-triggered
[4294715.964000] ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKA] -> GSI 5
(level, low) -> IRQ 5
[4294715.964000] rt2500 1.1.0 CVS 2005/07/10 http://rt2x00.serialmonkey.com
[4294718.553000] drivers/usb/class/usblp.c: usblp0: USB Bidirectional
printer dev 2 if 0 alt 0 proto 2 vid 0x03F0 pid 0x1904
[4294718.567000] usbcore: registered new driver usblp
[4294718.567000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class
driver
[4294718.902000] Real Time Clock Driver v1.12
[4294719.003000] input: PC Speaker
[4294719.313000] Floppy drive(s): fd0 is 1.44M
[4294719.327000] FDC 0 is a post-1991 82077
[4294721.174000] NET: Registered protocol family 17
[4294728.855000] NET: Registered protocol family 10
[4294728.855000] Disabled Privacy Extensions on device c0321b80(lo)
[4294728.856000] IPv6 over IPv4 tunneling driver
[4294730.907000] ACPI: Power Button (FF) [PWRF]
[4294730.907000] ACPI: Power Button (CM) [PWRB]
[4294730.907000] ACPI: Sleep Button (CM) [SLPB]
[4294731.124000] ibm_acpi: ec object not found
[4294739.829000] ra0: no IPv6 routers present
[4294748.499000] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[4294748.499000] apm: overridden by ACPI.
[4294751.775000] powernow: No powernow capabilities detected
[4294752.013000] Bluetooth: Core ver 2.7
[4294752.013000] NET: Registered protocol family 31
[4294752.013000] Bluetooth: HCI device and connection manager initialized
[4294752.013000] Bluetooth: HCI socket layer initialized
[4294752.055000] Bluetooth: L2CAP ver 2.7
[4294752.055000] Bluetooth: L2CAP socket layer initialized
[4294752.121000] Bluetooth: RFCOMM ver 1.5
[4294752.121000] Bluetooth: RFCOMM socket layer initialized
[4294752.121000] Bluetooth: RFCOMM TTY layer initialized
[4295079.952000] ibm_acpi: ec object not found
[4295304.089000] cdrom: open failed.
[4295304.098000] cdrom: open failed.
[4295304.334000] hda: task_in_intr: status=0x59 { DriveReady SeekComplete
DataRequest Error }
[4295304.334000] hda: task_in_intr: error=0x10 { SectorIdNotFound },
LBAsect=78230639, sector=78165360
[4295304.334000] ide: failed opcode was: unknown
[4295304.508000] hda: task_in_intr: status=0x59 { DriveReady SeekComplete
DataRequest Error }
[4295304.508000] hda: task_in_intr: error=0x10 { SectorIdNotFound },
LBAsect=78230639, sector=78165360
[4295304.508000] ide: failed opcode was: unknown
[4295304.683000] hda: task_in_intr: status=0x59 { DriveReady SeekComplete
DataRequest Error }
[4295304.683000] hda: task_in_intr: error=0x10 { SectorIdNotFound },
LBAsect=78230639, sector=78165360
[4295304.683000] ide: failed opcode was: unknown
[4295304.858000] hda: task_in_intr: status=0x59 { DriveReady SeekComplete
DataRequest Error }
[4295304.858000] hda: task_in_intr: error=0x10 { SectorIdNotFound },
LBAsect=78230639, sector=78165360
[4295304.858000] ide: failed opcode was: unknown
[4295304.908000] ide0: reset: success
[4295305.082000] hda: task_in_intr: status=0x59 { DriveReady SeekComplete
DataRequest Error }
[4295305.082000] hda: task_in_intr: error=0x10 { SectorIdNotFound },
LBAsect=78230639, sector=78165360
[4295305.082000] ide: failed opcode was: unknown
[4295305.257000] hda: task_in_intr: status=0x59 { DriveReady SeekComplete
DataRequest Error }
[4295305.257000] hda: task_in_intr: error=0x10 { SectorIdNotFound },
LBAsect=78230639, sector=78165360
[4295305.257000] ide: failed opcode was: unknown
[4295305.432000] hda: task_in_intr: status=0x59 { DriveReady SeekComplete
DataRequest Error }
[4295305.432000] hda: task_in_intr: error=0x10 { SectorIdNotFound },
LBAsect=78230639, sector=78165360
[4295305.432000] ide: failed opcode was: unknown
[4295305.607000] hda: task_in_intr: status=0x59 { DriveReady SeekComplete
DataRequest Error }
[4295305.607000] hda: task_in_intr: error=0x10 { SectorIdNotFound },
LBAsect=78230639, sector=78165360
[4295305.607000] ide: failed opcode was: unknown
[4295305.657000] ide0: reset: success
[4295305.831000] hda: task_in_intr: status=0x59 { DriveReady SeekComplete
DataRequest Error }
[4295305.831000] hda: task_in_intr: error=0x10 { SectorIdNotFound },
LBAsect=78230639, sector=78165360
[4295305.831000] ide: failed opcode was: unknown
[4295305.831000] end_request: I/O error, dev hda, sector 78165360
[4295330.257000] cdrom: open failed.
[4295330.265000] cdrom: open failed.
[4295330.457000] hda: task_in_intr: status=0x59 { DriveReady SeekComplete
DataRequest Error }
[4295330.457000] hda: task_in_intr: error=0x10 { SectorIdNotFound },
LBAsect=78230639, sector=78165360
[4295330.457000] ide: failed opcode was: unknown
[4295330.632000] hda: task_in_intr: status=0x59 { DriveReady SeekComplete
DataRequest Error }
[4295330.632000] hda: task_in_intr: error=0x10 { SectorIdNotFound },
LBAsect=78230639, sector=78165360
[4295330.632000] ide: failed opcode was: unknown
[4295330.807000] hda: task_in_intr: status=0x59 { DriveReady SeekComplete
DataRequest Error }
[4295330.807000] hda: task_in_intr: error=0x10 { SectorIdNotFound },
LBAsect=78230639, sector=78165360
[4295330.807000] ide: failed opcode was: unknown
[4295330.981000] hda: task_in_intr: status=0x59 { DriveReady SeekComplete
DataRequest Error }
[4295330.981000] hda: task_in_intr: error=0x10 { SectorIdNotFound },
LBAsect=78230639, sector=78165360
[4295330.981000] ide: failed opcode was: unknown
[4295331.032000] ide0: reset: success
[4295331.206000] hda: task_in_intr: status=0x59 { DriveReady SeekComplete
DataRequest Error }
[4295331.206000] hda: task_in_intr: error=0x10 { SectorIdNotFound },
LBAsect=78230639, sector=78165360
[4295331.206000] ide: failed opcode was: unknown
[4295331.381000] hda: task_in_intr: status=0x59 { DriveReady SeekComplete
DataRequest Error }
[4295331.381000] hda: task_in_intr: error=0x10 { SectorIdNotFound },
LBAsect=78230639, sector=78165360
[4295331.381000] ide: failed opcode was: unknown
[4295331.556000] hda: task_in_intr: status=0x59 { DriveReady SeekComplete
DataRequest Error }
[4295331.556000] hda: task_in_intr: error=0x10 { SectorIdNotFound },
LBAsect=78230639, sector=78165360
[4295331.556000] ide: failed opcode was: unknown
[4295331.731000] hda: task_in_intr: status=0x59 { DriveReady SeekComplete
DataRequest Error }
[4295331.731000] hda: task_in_intr: error=0x10 { SectorIdNotFound },
LBAsect=78230639, sector=78165360
[4295331.731000] ide: failed opcode was: unknown
[4295331.781000] ide0: reset: success
[4295331.955000] hda: task_in_intr: status=0x59 { DriveReady SeekComplete
DataRequest Error }
[4295331.955000] hda: task_in_intr: error=0x10 { SectorIdNotFound },
LBAsect=78230639, sector=78165360
[4295331.955000] ide: failed opcode was: unknown
[4295331.955000] end_request: I/O error, dev hda, sector 78165360
Y ya que estoy ¿alguien me puede decir los I/O error a que se deben? Antes
de usar Ubuntu yo usaba Suse y cuando me instale la 9.1 me daba estos
errores, debido al paso al núcleo 2.6.X. Al ejecutar dmesg me he dado cuenta
de que ubuntu tb me da este error. Mi disco duro no esta roto ni tiene
sectores defectuosos, ya lo he testeado.
Un saludo y gracias.
El día 13/03/06, Jorge Mauricio Hernandez Torres <jmauricio en gmail.com>
escribió:
>
> On 3/13/06, Manuel Grau Aracil <invocationtargetexception en gmail.com>
> wrote:
> > Mirar que me jode esto, pero no me termina de ir bien la red inalámbrica
> en
> > linux. No es problema de hardware, con windows va perfecto (a mi pesar
> que
> > en algo vaya mejor que linux). Me esta tocando las narices, porque va
> cuando
> > le da la gana. Como no se mucho de configuracion a pelo de red en linux,
> no
> > se como mirar que pasa. He ejecutado ifconfig y he comprobado que tengo
> ip.
> > Puedo hacer un ping a mi router inalámbrico y a mi portátil con cliente
> > windows sin problema, pero no sale a internet. La red esta configurada
> por
> > DHCP con la utilidad gráfica que lleva Ubuntu Breezy, y el dispositivo
> esta
> > activado y funcionando. En windows veo las dos dns que me ha asignado.
> He
> > mirado resolv.conf y tengo las siguientes lineas:
>
> Hola Manuel, un poco de paciencia, que yo he estado en las mismas
> adaptando un a tarjeta usb dell 1180 a una powerbook (todavia no meto
> el firmware para que funcione la airport extreme)
>
> que te indica la salida del comando dmesg ?
>
> si das un: sudo iwconfig tu_interfaz_de_red essid essid_asignado que te
> manda?
> luego sudo dhclient interfaz_de_red que te dice?
>
> Tranquilo, que para vida sencilla y facil, llena de virus, spyware y
> troyanos esta el windows.
>
> Saludos,
> Jorge Mauricio
> --
> <blog>
> http://djmaucom.blogspot.com
> http://jmauricio.blogspot.com
> </blog>
>
------------ próxima parte ------------
Se ha borrado un adjunto en formato HTML...
URL: https://lists.ubuntu.com/archives/ubuntu-es/attachments/20060323/95854ea8/attachment-0001.htm
Más información sobre la lista de distribución ubuntu-es