[ubuntu-it] installazione wi-fi BCM43XX ???? :(
lele
bonnastudio a tele2.it
Gio 8 Feb 2007 23:36:29 GMT
Il giorno gio, 08/02/2007 alle 18.09 +0100, pietro barnabè ha scritto:
> On Thu, 08 Feb 2007 20:35:32 +0100
> lele <bonnastudio a tele2.it> wrote:
>
> > Il giorno gio, 08/02/2007 alle 20.00 +0100, lele ha scritto:
> > > Ciao ragassi :) sono disperato :(
> > >
> > > E' da tre settimane che cerco di far funzionare la mia wi-fi integrata
> > > nel mio pc pavilion hp 5463a ho seguito la wiki di ubuntu a lseguente
> > > link: http://wiki.ubuntu-it.org/BroadcomBcm4306?highlight=%28Broadcom%
> > > 29%7C%284306%29
> > >
> > > tutto bene fino a quando installo i drive che ho scaricato dopo aver
> > > inserito il comando sudo ndiswrapper -i bcmwl5.inf tutto ok poi per
> > > verificare il tutto lancio il comando ndiswrapper -l e come risposta
> > > ho:
> > >
> > > Installed ndis drivers:
> > > bcmwl5 invalid driver!
> > > bcmwl5.sys invalid driver!
> > >
> > > ok i driver non sono quelli giusti, ma sta cosa mi pare strana... io ho
> > > il seguente hardware come wi-fi 02:02.0 Network controller: Broadcom
> > > Corporation BCM4306 802.11b/g Wireless LAN Controller (rev 03)
> > >
> > > quindi dovrebbe andare bene con quello che è menzionato nella wiki
> > > ovvero: 0000:0b:03.0 Network controller: Broadcom Corporation BCM43XX
> > > 802.11b/g Wireless LAN Controller (rev 03)
> > >
> > > per di più se cerco di reinstallarlo mi dice che è già presente e devo
> > > toglierlo prima di reinstallarlo..:( come posso eliminare i 2 files che
> > > ho installato??? dove trovo i driver ?? visto che sul sito ufficiale non
> > > ci stanno?? grazie mille per la vostra pazienza
> > >
> > >
> > >
> > >
> > >
> > aggiungo che dopo aver lanciato il comando ./makefile install per
> > compilare i driver, mi dice quanto segue:
> >
> > ./Makefile install
> > ./Makefile: line 1: VERSION: command not found
> > ./Makefile: line 3: FIRMWARE_INSTALL_DIR: command not found
> > ./Makefile: line 5: CC: command not found
> > ./Makefile: line 6: PREFIX: command not found
> > ./Makefile: line 7: CFLAGS: command not found
> > ./Makefile: line 8: CFLAGS: command not found
> > ./Makefile: line 9: LDFLAGS: command not found
> > ./Makefile: line 12: OBJECTS: command not found
> > ./Makefile: line 14: VERSION: command not found
> > ./Makefile: line 14: CFLAGS: command not found
> > ./Makefile: line 16: all:: command not found
> > ./Makefile: line 18: OBJECTS: command not found
> > ./Makefile: line 18: fwcutter:: command not found
> > ./Makefile: line 19: CC: command not found
> > ./Makefile: line 19: CFLAGS: command not found
> > ./Makefile: line 19: OBJECTS: command not found
> > ./Makefile: line 19: LDFLAGS: command not found
> > ./Makefile: line 19: -o: command not found
> > ./Makefile: line 21: install:: command not found
> > ./Makefile: line 22: PREFIX: command not found
> > ./Makefile: line 22: -install: command not found
> > ./Makefile: line 23: PREFIX: command not found
> > ./Makefile: line 23: -install: command not found
> > ./Makefile: line 24: PREFIX: command not found
> > ./Makefile: line 24: -install: command not found
> > ./Makefile: line 25: PREFIX: command not found
> > ./Makefile: line 25: -install: command not found
> > ./Makefile: line 27: clean:: command not found
> > ./Makefile: line 28: -rm: command not found
> > ./Makefile: line 30: installfw:: command not found
> > ./Makefile: line 31: syntax error near unexpected token `then'
> > ./Makefile: line 31: ` -if ! [ -d $(FIRMWARE_INSTALL_DIR) ]; then mkdir
> > -p $(FIRMWARE_INSTALL_DIR); fi'
> >
> >
> > dove toppo?? per compilarli in modo corretto che comando gli devo dare??
> >
> >
> > grazie tante e tutti un giorno spero di dare una mano ha chi ne ha
> > bisogno :(
>
> Hai installato i linux-headers corrispondenti il tuo kernel?
> Oppure se c'è stato un aggiornamento del kernel, li hai aggiornati, ed hai aggiornato il link simbolico /usr/src/linux facendolo puntare ai nuovi headers?
>
> comunque, il comando potrebbe essere: make dato all'interno della cartella che contiene i driver da compilare, per averne la certezza, prova a leggere un file README o INSTALL all'interno della cartella dei driver. Lì ci dovrebbero essere tutte le indicazioni per installare.
>
> ciao, Pietro
"Hai installato i linux-headers corrispondenti il tuo kernel?
Oppure se c'è stato un aggiornamento del kernel, li hai aggiornati, ed
hai aggiornato il link simbolico /usr/src/linux facendolo puntare ai
nuovi headers?"
?? o mamma come si fa a fare quello che dici?? credo di non aver fatto tutto ciò..cmq il mio kernel è il seguente:
ubuntu 6.10 edgy eft x86 versione 2.6.17-10 e il mio linux headers è 2.6.17-10...non credo sia necessario un agg ??o??
ho letto dentro il file readme è non ci ho capito molto:
"BCM43XX Linux Driver Project
============================
About this software
-------------------
bcm43xx-fwcutter is a tool which can extract firmware from various source files.
It's written for BCM43xx driver files.
The project page is http://bcm43xx.berlios.de/
Usage
-----
bcm43xx-fwcutter FILE extracts the firmware from a source FILE to .
bcm43xx-fwcutter -i FILE identify the driver file. Print information, but don't extract.
bcm43xx-fwcutter -w /tmp FILE extract and write firmware to /tmp.
bcm43xx-fwcutter -l prints a list of supported driver source files.
After extraction, run make installfw which will copy bcm43xx_*.fw to
FIRMWARE_INSTALL_DIR (which defaults to /lib/firmware) for
usage by the bcm43xx driver. An alternative way is using the -w option.
Different distributions use different target directories for the firmware
files. If the driver complains about missing firmware files look for the
correct directory. For some distributions you have to use
/lib/hotplug/firmware or /usr/lib/hotplug/firmware for FIRMWARE_INSTALL_DIR,
but other directories are also possible.
Extraction doesn't depend on the system you're using. You can even
extract firmware on ppc from a mips driver. Cross-extraction is allowed.
Where can I find some driver source files?
------------------------------------------
AppleAirPort2
-------------
You can find the Apple Airport Extreme driver in your Mac OS X system at
/System/Library/Extensions/AppleAirPort2.kext/Contents/MacOS/AppleAirPort2
(Note that not all versions of the MacOSX driver are supported.)
AppleAirPortBrcm4311
--------------------
AppleAirPortBrcm4311 only seems to be available on Intel based machines.
System/Library/Extensions/IO80211Family.kext/Contents/PlugIns/AppleAirPortBrcm4311.kext/Contents/MacOS/AppleAirPortBrcm4311
bcmwl5.sys"
mi sa che devo cercare i driver sotto windows, ma trovo solo il file .sys e non .inf ?? mo ci riprovo...
è diventata una cosa privata..deve andare.. la macchina si deve inclinare al mio volere ;)
grazie di tutto
Maggiori informazioni sulla lista
ubuntu-it