Maxtor Mini External Hard Drive
Tony Corbett
corbtr at hotmail.com
Fri Apr 11 21:22:41 UTC 2008
Corey, tried "demesg" and it does seem to detect the ehd, as shown below.
any suggestions on what next?
cheers
tony
[ 22.525387] hub 3-0:1.0: USB hub found
[ 22.525402] hub 3-0:1.0: 2 ports detected
[ 22.542738] FDC 0 is a post-1991 82077
[ 22.630031] ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 16
[ 22.630051] ehci_hcd 0000:00:10.3: EHCI Host Controller
[ 22.630105] ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
[ 22.630165] ehci_hcd 0000:00:10.3: irq 16, io mem 0xde010000
[ 22.630172] ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 22.630307] usb usb4: configuration #1 chosen from 1 choice
[ 22.630342] hub 4-0:1.0: USB hub found
[ 22.630357] hub 4-0:1.0: 6 ports detected
[ 22.660090] usb 1-1: new full speed USB device using uhci_hcd and address 2
[ 22.733815] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 18 (level, low) -> IRQ 17
[ 22.734094] eth0: RealTek RTL8139 at 0xde862000, 00:0d:61:34:eb:5c, IRQ 17
[ 22.734097] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[ 22.734299] VP_IDE: IDE controller at PCI slot 0000:00:11.1
[ 22.734697] ACPI: PCI Interrupt Link [ALKA] BIOS reported IRQ 0, using IRQ 20
[ 22.734700] ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
[ 22.734706] ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 18
[ 22.734716] VP_IDE: chipset revision 6
[ 22.734718] VP_IDE: not 100% native mode: will probe irqs later
[ 22.734730] VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
[ 22.734739] ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:pio
[ 22.734752] ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:pio
[ 22.734761] Probing IDE interface ide0...
[ 22.745723] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 23.147566] hda: SAMSUNG SP0411N, ATA DISK drive
[ 23.602951] usb 4-1: new high speed USB device using ehci_hcd and address 2
[ 23.750877] usb 4-1: configuration #1 chosen from 1 choice
[ 23.764775] usbcore: registered new interface driver libusual
[ 23.769697] Initializing USB Mass Storage driver...
[ 23.769818] scsi0 : SCSI emulation for USB Mass Storage devices
[ 23.769885] usbcore: registered new interface driver usb-storage
[ 23.769889] USB Mass Storage support registered.
[ 23.770000] usb-storage: device found at 2
[ 23.770002] usb-storage: waiting for device to settle before scanning
[ 23.818873] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 23.825366] Probing IDE interface ide1...
[ 24.685777] hdc: HL-DT-ST DVDRAM GSA-H42N, ATAPI CD/DVD-ROM drive
[ 25.022467] ide1 at 0x170-0x177,0x376 on irq 15
[ 25.035944] hda: max request size: 512KiB
[ 25.047613] hda: 78242976 sectors (40060 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
[ 25.047839] hda: cache flushes supported
[ 25.047898] hda: hda1 hda2 < hda5 >
[ 25.088136] hdc: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(66)
[ 25.088148] Uniform CD-ROM driver Revision: 3.20
[ 25.293424] Attempting manual resume
[ 25.293430] swsusp: Resume From Partition 3:5
[ 25.293432] PM: Checking swsusp image.
[ 25.293612] PM: Resume from disk failed.
[ 25.309864] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 25.309870] EXT3-fs: write access will be enabled during recovery.
[ 28.732933] kjournald starting. Commit interval 5 seconds
[ 28.732958] EXT3-fs: recovery complete.
[ 28.733189] EXT3-fs: mounted filesystem with ordered data mode.
[ 28.761083] usb-storage: device scan complete
[ 29.506787] scsi 0:0:0:0: Direct-Access Maxtor OneTouch III 0364 PQ: 0 ANSI: 4
[ 37.494918] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 38.724214] NET: Registered protocol family 17
[ 39.430687] Linux agpgart interface v0.102 (c) Dave Jones
[ 39.449000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 39.469452] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 39.540104] agpgart: Detected VIA KM400/KM400A chipset
[ 39.548116] agpgart: AGP aperture is 128M @ 0xd0000000
[ 39.872983] irda_init()
[ 39.873017] NET: Registered protocol family 23
[ 40.121840] input: PC Speaker as /class/input/input2
[ 40.249591] parport: PnPBIOS parport detected.
[ 40.249640] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 40.374224] input: ImPS/2 Generic Wheel Mouse as /class/input/input3
[ 40.651511] sda: Unit Not Ready, sense:
[ 40.651518] : Current: sense key: Illegal Request
[ 40.651521] Additional sense: Invalid command operation code
[ 40.653914] SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB)
[ 40.658709] sda: test WP failed, assume Write Enabled
[ 40.658715] sda: assuming drive cache: write through
[ 40.664999] sda: Unit Not Ready, sense:
[ 40.665005] : Current: sense key: Illegal Request
[ 40.665008] Additional sense: Invalid command operation code
[ 40.665500] SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB)
[ 40.666620] sda: test WP failed, assume Write Enabled
[ 40.666624] sda: assuming drive cache: write through
[ 40.666630] sda:end_request: I/O error, dev sda, sector 0
[ 40.667748] Buffer I/O error on device sda, logical block 0
[ 40.670347] Buffer I/O error on device sda, logical block 0
[ 40.671487] end_request: I/O error, dev sda, sector 0
[ 40.681599] end_request: I/O error, dev sda, sector 24
[ 40.682722] end_request: I/O error, dev sda, sector 0
[ 40.682728] unknown partition table
[ 40.683026] sd 0:0:0:0: Attached scsi disk sda
[ 40.710197] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 40.746823] ACPI: PCI Interrupt Link [ALKC] BIOS reported IRQ 0, using IRQ 22
[ 40.746829] ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
[ 40.746840] ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [ALKC] -> GSI 22 (level, low) -> IRQ 19
[ 40.747186] PCI: Setting latency timer of device 0000:00:11.5 to 64
[ 40.763829] end_request: I/O error, dev sda, sector 195371392
[ 40.807690] end_request: I/O error, dev sda, sector 0
[ 40.808813] end_request: I/O error, dev sda, sector 0
[ 41.438758] fuse init (API version 7.8)
[ 41.471211] lp0: using parport0 (interrupt-driven).
[ 41.504005] Adding 1413680k swap on /dev/disk/by-uuid/9399d3fb-bdb3-4cd7-82e7-48fcfe08e927. Priority:-1 extents:1 across:1413680k
[ 41.625417] EXT3 FS on hda1, internal journal
[ 41.760819] NET: Registered protocol family 10
[ 41.760928] lo: Disabled Privacy Extensions
[ 46.999080] input: Power Button (FF) as /class/input/input4
[ 47.004106] ACPI: Power Button (FF) [PWRF]
[ 47.043112] input: Power Button (CM) as /class/input/input5
[ 47.048175] ACPI: Power Button (CM) [PWRB]
[ 47.203711] ibm_acpi: ec object not found
[ 47.240090] No dock devices found.
[ 47.292642] Using specific hotkey driver
[ 47.368261] pcc_acpi: loading...
[ 50.682713] end_request: I/O error, dev sda, sector 195371392
[ 50.682722] printk: 44 messages suppressed.
[ 50.682726] Buffer I/O error on device sda, logical block 24421424
[ 50.684448] end_request: I/O error, dev sda, sector 195371392
[ 50.684452] Buffer I/O error on device sda, logical block 24421424
[ 50.733136] end_request: I/O error, dev sda, sector 0
[ 52.427724] [drm] Initialized drm 1.1.0 20060810
[ 52.455034] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 20
[ 52.458719] [drm] Initialized via 2.11.0 20061227 on minor 0
[ 52.508086] agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
[ 52.508431] agpgart: Device is in legacy mode, falling back to 2.x
[ 52.514096] [drm:via_mem_alloc] *ERROR* Attempt to allocate from uninitialized memory manager.
[ 52.603145] ppdev: user-space parallel port driver
[ 53.479971] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[ 53.479978] apm: overridden by ACPI.
[ 53.658274] Bluetooth: Core ver 2.11
[ 53.658361] NET: Registered protocol family 31
[ 53.658364] Bluetooth: HCI device and connection manager initialized
[ 53.658368] Bluetooth: HCI socket layer initialized
[ 53.704213] Bluetooth: L2CAP ver 2.8
[ 53.704219] Bluetooth: L2CAP socket layer initialized
[ 53.802319] Bluetooth: RFCOMM socket layer initialized
[ 53.802340] Bluetooth: RFCOMM TTY layer initialized
[ 53.802342] Bluetooth: RFCOMM ver 1.8
[ 68.051187] eth0: no IPv6 routers present
[ 1528.694223] usb 4-1: USB disconnect, address 2
[ 2105.862046] usb 4-2: new high speed USB device using ehci_hcd and address 3
[ 2106.014119] usb 4-2: configuration #1 chosen from 1 choice
[ 2106.014393] scsi1 : SCSI emulation for USB Mass Storage devices
[ 2106.014557] usb-storage: device found at 3
[ 2106.014559] usb-storage: waiting for device to settle before scanning
[ 2111.012214] usb-storage: device scan complete
[ 2111.778253] scsi 1:0:0:0: Direct-Access Maxtor OneTouch III 0364 PQ: 0 ANSI: 4
[ 2111.811409] sda: Unit Not Ready, sense:
[ 2111.811416] : Current: sense key: Illegal Request
[ 2111.811418] Additional sense: Invalid command operation code
[ 2111.812098] SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB)
[ 2111.813157] sda: test WP failed, assume Write Enabled
[ 2111.813161] sda: assuming drive cache: write through
[ 2111.815776] sda: Unit Not Ready, sense:
[ 2111.815779] : Current: sense key: Illegal Request
[ 2111.815781] Additional sense: Invalid command operation code
[ 2111.816423] SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB)
[ 2111.817526] sda: test WP failed, assume Write Enabled
[ 2111.817529] sda: assuming drive cache: write through
[ 2111.817533] sda:end_request: I/O error, dev sda, sector 0
[ 2111.818654] printk: 38 messages suppressed.
[ 2111.818657] Buffer I/O error on device sda, logical block 0
[ 2111.819771] end_request: I/O error, dev sda, sector 0
[ 2111.819775] Buffer I/O error on device sda, logical block 0
[ 2111.828760] end_request: I/O error, dev sda, sector 0
[ 2111.828764] Buffer I/O error on device sda, logical block 0
[ 2111.829883] end_request: I/O error, dev sda, sector 0
[ 2111.831007] end_request: I/O error, dev sda, sector 24
[ 2111.832130] end_request: I/O error, dev sda, sector 24
[ 2111.833254] end_request: I/O error, dev sda, sector 0
[ 2111.833262] unknown partition table
[ 2111.833319] sd 1:0:0:0: Attached scsi disk sda
[ 2111.833373] sd 1:0:0:0: Attached scsi generic sg0 type 0
[ 2112.004301] end_request: I/O error, dev sda, sector 195371392
[ 2112.005785] end_request: I/O error, dev sda, sector 195371392
[ 2112.154847] end_request: I/O error, dev sda, sector 0
[ 2623.639096] usb 4-2: USB disconnect, address 3
[ 2634.634261] usb 4-2: new high speed USB device using ehci_hcd and address 4
[ 2634.782338] usb 4-2: configuration #1 chosen from 1 choice
[ 2634.782599] scsi2 : SCSI emulation for USB Mass Storage devices
[ 2634.782761] usb-storage: device found at 4
[ 2634.782763] usb-storage: waiting for device to settle before scanning
[ 2639.776429] usb-storage: device scan complete
[ 2640.543227] scsi 2:0:0:0: Direct-Access Maxtor OneTouch III 0364 PQ: 0 ANSI: 4
[ 2640.576495] sda: Unit Not Ready, sense:
[ 2640.576503] : Current: sense key: Illegal Request
[ 2640.576506] Additional sense: Invalid command operation code
[ 2640.577205] SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB)
[ 2640.601216] sda: test WP failed, assume Write Enabled
[ 2640.601220] sda: assuming drive cache: write through
[ 2640.603834] sda: Unit Not Ready, sense:
[ 2640.603837] : Current: sense key: Illegal Request
[ 2640.603839] Additional sense: Invalid command operation code
[ 2640.604388] SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB)
> Date: Thu, 10 Apr 2008 10:43:40 -0400
> From: corey at 31415926535.com
> To: ubuntu-users at lists.ubuntu.com
> Subject: Re: Maxtor Mini External Hard Drive
>
> Tony Corbett wrote:
> > yep , its usb, and definately plugged in
> > and not showing in PLACES
> >
> >> Corey Bettenhausen wrote:
> >>> Tony Corbett wrote:
> >>>> Hi, I have just loaded Ubuntu 7.04 to give it a go and need to figure out how to get my EHD connected.
> >>>>
> >>>> I have previously reloaded Windows NT I have had to download software for the EHD from the Seagate / Maxtor tech support site. This site makes no referecne ot reqyiuirmeents for linux etc.
> >>>>
> >>>> I have a Maxtor One touch III Mini ehd.
> >>>>
> >>>> Any help would be great. Keep it simple - im new to U.
> >>>>
> >>>> Cheers Tony
> >>> I'm not familiar with the particular drive that you mention, but I'll
> >>> assume it's a USB or firewire drive? If so, have you just tried to plug
> >>> it in?
> >>> -Corey
> >> Further, Windows NT didn't natively support USB. That's why you had to
> >> install software from Maxtor to get it to work. Ubuntu does support
> >> USB. So you should be able to just plug it in and it should show up on
> >> your desktop or through "Places" in the menu bar at the top of your screen.
> >> Cheers,
> >> -Corey
>
> Has the drive been formatted yet?
> To see if the drive has been detected at all, open a terminal window
> (Applications -> Accessories -> Terminal), plug in the drive, and type
> "dmesg" (without quotes) in the terminal window. If the drive is being
> detected, you should see some lines indicating that a new USB device has
> been attached.
> -Corey
>
> --
> ubuntu-users mailing list
> ubuntu-users at lists.ubuntu.com
> Modify settings or unsubscribe at: https://lists.ubuntu.com/mailman/listinfo/ubuntu-users
_________________________________________________________________
It's simple! Sell your car for just $30 at CarPoint.com.au
http://a.ninemsn.com.au/b.aspx?URL=http%3A%2F%2Fsecure%2Dau%2Eimrworldwide%2Ecom%2Fcgi%2Dbin%2Fa%2Fci%5F450304%2Fet%5F2%2Fcg%5F801459%2Fpi%5F1004813%2Fai%5F859641&_t=762955845&_r=tig_OCT07&_m=EXT
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://lists.ubuntu.com/archives/ubuntu-users/attachments/20080412/860acfd8/attachment.html>
More information about the ubuntu-users
mailing list