[USB] Monter une clé USB

[adeimantos at free.fr]

Selon Christophe Lucas <clucas at rotomalug.org>:

> adeimantos at free.fr (adeimantos at free.fr) wrote:
> >
> >
> > Cher Amis : il y a du nouveau !
> > Après avoir fait les opérations suivantes
> > 1)  mknod /dev/sda1 b 8 1
> > 2) mkdir /media/clusb
> > 3) Dans /etc/fstab, ajouté la ligne :
> > /dev/sda1 /media/clusb   vfat    rw,user,noauto  0   0
> >
> > 4) Passé la commande suivante :
> > modprobe usb-storage
> >
> > 5) réinstallé les paquets 'acpi' ...
> >
> > 5) relancé le système ...
> >
> > Lorsque je branche ma clé USB, la petite lumière verte clignote et j'ai
> bien
> > dans 'Poste de travail' l'icône 'clusb'. Lorsque je clique sur cette icône,
> le
> > système renvoie une boîte de dialogue qui dit :
> > mount: special device /dev/sda1 does not exist
> >
> > Je suppose que la commande 1) n'est pas la bonne...Quand pensez-vous ?
> > JP
>
> Que donne 'dmesg' à ce moment ci.
>
> 	~Christophe
>
'dmesg' (concernant USB) renvoie ça :
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:07.2[D] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:07.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:07.2: irq 5, io base 0000e400
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
8139too Fast Ethernet driver 0.9.27
ACPI: PCI interrupt 0000:00:12.0[A] -> GSI 12 (level, low) -> IRQ 12
eth0: RealTek RTL8139 at 0xe800, 00:80:ad:7a:9a:a7, IRQ 12
eth0:  Identified 8139 chip type 'RTL-8100'
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ACPI: PCI interrupt 0000:00:14.0[A] -> GSI 5 (level, low) -> IRQ 5
ohci_hcd 0000:00:14.0: Lucent Microelectronics USS-344S USB Controller
ohci_hcd 0000:00:14.0: irq 5, pci mem d4a2d000
ohci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
ACPI: PCI interrupt 0000:00:14.1[A] -> GSI 5 (level, low) -> IRQ 5
ohci_hcd 0000:00:14.1: Lucent Microelectronics USS-344S USB Controller (#2)
ohci_hcd 0000:00:14.1: irq 5, pci mem d4a49000
ohci_hcd 0000:00:14.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
ACPI: PCI interrupt 0000:00:14.2[A] -> GSI 5 (level, low) -> IRQ 5
ohci_hcd 0000:00:14.2: Lucent Microelectronics USS-344S USB Controller (#3)
ohci_hcd 0000:00:14.2: irq 5, pci mem d4a52000
ohci_hcd 0000:00:14.2: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
ACPI: PCI interrupt 0000:00:14.3[A] -> GSI 5 (level, low) -> IRQ 5
ohci_hcd 0000:00:14.3: Lucent Microelectronics USS-344S USB Controller (#4)
ohci_hcd 0000:00:14.3: irq 5, pci mem d4a66000
ohci_hcd 0000:00:14.3: new USB bus registered, assigned bus number 5
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 1 port detected
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
Linux Kernel Card Services
  options:  [pci] [cardbus] [pm]
Intel ISA PCIC probe: not found.
Device 'i823650' does not have a release() function, it is broken and must be
fixed.
Badness in device_release at drivers/base/core.c:85
 [<c018bbd8>] kobject_cleanup+0x40/0x65
 [<d4839e11>] init_i82365+0x6f/0x179 [i82365]
 [<c012afd2>] sys_init_module+0xe3/0x1d4
 [<c0105f9b>] syscall_call+0x7/0xb
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02c95c0(lo)
IPv6 over IPv4 tunneling driver
usb 2-1: new full speed USB device using address 2
usb 2-1: control timeout on ep0out
ohci_hcd 0000:00:14.0: Unlink after no-IRQ?  Different ACPI or APIC settings may
help.